CY7C4265-10ASC(2004) 데이터 시트보기 (PDF) - Cypress Semiconductor
부품명
상세내역
일치하는 목록
CY7C4265-10ASC Datasheet PDF : 22 Pages
| |||
CY7C4255
CY7C4265
Signal Name Description I/O
Function
D0 –17
Q0–17
WEN
Data Inputs
Data Outputs
Write Enable
I Data inputs for an 18-bit bus.
O Data outputs for an 18-bit bus.
I Enables the WCLK inpu.t
REN
Read Enable
I Enables the RCLK input.
WCLK
Write Clock
I The rising edge clocks data into the FIFO when WEN is LOW and the FIFO is not
Full. When LD is asserted, WCLK writes data into the programmable flag-offset
register.
RCLK
Read Clock
I The rising edge clocks data out of the FIFO when REN is LOW and the FIFO is not
Empty. When LD is asserted, RCLK reads data out of the programmable flag-off-
set register.
WXO/HF
Write Expansion O Dual-Mode Pin:
Out/Half Full Flag
Single device or width expansion – Half Full status flag.
Cascaded – Write Expansion Out signal, connected to WXI of next device.
EF
Empty Flag
O When EF is LOW, the FIFO is empty. EF is synchronized to RCLK.
FF
Full Flag
O When FF is LOW, the FIFO is full. FF is synchronized to WCLK.
PAE
Programmable
O When PAE is LOW, the FIFO is almost empty based on the almost-empty offset
Almost Empty
value programmed into the FIFO. PAE is asynchronous when VCC/SMODE is tied
to VCC; it is synchronized to RCLK when VCC/SMODE is tied to VSS.
PAF
Programmable
O When PAF is LOW, the FIFO is almost full based on the almost full offset value
Almost Full
programmed into the FIFO. PAF is asynchronous when VCC/SMODE is tied to
VCC; it is synchronized to WCLK when VCC/SMODE is tied to VSS.
LD
Load
I When LD is LOW, D0–17 (Q0–17) are written (read) into (from) the programma-
ble-flag-offset register.
FL/RT
First Load/
Retransmit
I Dual-Mode Pin:
Cascaded – The first device in the daisy chain will have FL tied to VSS; all other
devices will have FL tied to VCC. In standard mode or width expansion, FL is tied
to VSS on all devices.
Not Cascaded – Tied to VSS. Retransmit function is also available in stand-alone
mode by strobing RT.
WXI
RXI
RXO
Write Expansion
Input
Read Expansion
Input
Read Expansion
Output
I Cascaded – Connected to WXO of previous device.
Not Cascaded – Tied to VSS.
I Cascaded – Connected to RXO of previous device.
Not Cascaded – Tied to VSS.
O Cascaded – Connected to RXI of next device.
RS
Reset
I Resets device to empty condition. A reset is required before an initial read or write
operation after power-up.
OE
Output Enable
I When OE is LOW, the FIFO’s data outputs drive the bus to which they are con-
nected. If OE is HIGH, the FIFO’s outputs are in High Z (high-impedance) state.
VCC/SMODE Synchronous
Almost Empty/
Almost Full Flags
I Dual-Mode Pin:
Asynchronous Almost Empty/Almost Full flags – tied to VCC.
Synchronous Almost Empty/Almost Full flags – tied to VSS.
(Almost Empty synchronized to RCLK, Almost Full synchronized to WCLK.)
Document #: 38-06004 Rev. *B
Page 3 of 22
Share Link: 