7411(2017) 데이터 시트보기 (PDF) - Analog Devices
부품명
상세내역
일치하는 목록
7411
(Rev.:2017)
(Rev.:2017)
Analog Devices
7411 Datasheet PDF : 36 Pages
| |||
ADT7411
Data Sheet
PIN CONFIGURATION AND FUNCTIONAL DESCRIPTIONS
AIN6 1
AIN5 2
NC 3
CS 4
GND 5
VDD 6
D+/AIN1 7
D–/AIN2 8
16 AIN7
ADT7411
TOP VIEW
(Not to Scale)
15 AIN8
14 AIN4
13 SCL/SCLK
12 SDA/DIN
11 DOUT/ADD
10 INT/INT
9 AIN3
NC = NO CONNECT
Figure 6. Pin Configuration
Table 4. Pin Function Descriptions
Pin
No. Mnemonic Description
1 AIN6
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
2 AIN5
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
3 NC
No Connection.
4 CS
SPI—Active Low Control Input. This is the frame synchronization signal for the input data. When CS goes low, it
enables the input register and data is transferred in on the rising edges and out on the falling edges of the subsequent
serial clocks. It is recommended that this pin be tied high to VDD when operating the serial interface in I2C mode.
5 GND
Ground Reference Point for All Circuitry on the Part. Analog and digital ground.
6
VDD
Positive Supply Voltage, 2.7 V to 5.5 V. The supply should be decoupled to ground.
7 D+/AIN1
Positive Connection to External Temperature Sensor/Analog Input. Single-ended analog input channel.
Input range is 0 V to 2.25 V or 0 V to 5 V.
8 D−/AIN2
Negative Connection to External Temperature Sensor/Analog Input. Single-ended analog input channel.
Input range is 0 V to 2.25 V or 0 V to 5 V.
9 AIN3
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
10 INT/INT
Overlimit Interrupt. The output polarity of this pin can be set to give an active low or active high interrupt when
temperature, VDD, or AIN limits are exceeded. Default is active low. Open-drain output needs a pull-up resistor.
11 DOUT/ADD DOUT—SPI Serial Data Output. Logic output. Data is clocked out of any register at this pin. Data is clocked out on the
falling edge of SCLK. Open-drain output needs a pull-up resistor.
ADD—I2C Serial Bus Address Selection Pin. Logic input. A low on this pin gives the Address 1001 000, while leaving it
floating gives the Address 1001 010 and setting it high gives the Address 1001 011. The I2C address set up by the
ADD pin is not latched by the device until after this address has been sent twice. On the eighth SCL cycle of the
second valid communication, the serial bus address is latched in. Any subsequent changes on this pin have no
effect on the I2C serial bus address.
12 SDA/DIN
SDA—I2C Serial Data Input. I2C serial data to be loaded into the part’s registers is provided on this input. An open-
drain configuration needs a pull-up resistor.
DIN—SPI Serial Data Input. Serial data to be loaded into the part’s registers is provided on this input. Data is
clocked into a register on the rising edge of SCLK. An open-drain configuration needs a pull-up resistor.
13 SCL/SCLK
Serial Clock Input. This is the clock input for the serial port. The serial clock is used to clock data out of any register
of the ADT7411 and to clock data into any register that can be written to. An open-drain configuration needs a pull-
up resistor.
14 AIN4
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
15 AIN8
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
16 AIN7
Analog Input. Single-ended analog input channel. Input range is 0 V to 2.25 V or 0 V to VDD.
Rev. C | Page 8 of 36
Share Link: