General Description
Introduction
The MC68HC908GZ60, MC68HC908GZ48, and MC68HC908GZ32 are members of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types.

FEATUREs
For convenience, features have been organized to reflect:
• Standard features
• Features of the CPU08

Standard Features
Features of the MC68HC908GZ60 include:
• High-performance M68HC08 architecture optimized for C-compilers
• Fully upward-compatible object code with M6805, M146805, and M68HC05 Families
• 8-MHz internal bus frequency
• Clock generation module supporting 1-MHz to 8-MHz crystals
• MSCAN08 (scalable controller area network) controller (implementing 2.0b protocol as defined in BOSCH specification dated September 1991)
• FLASH program memory security(1)
• On-chip programming firmware for use with host personal computer which does not require high voltage for entry
• In-system programming (ISP)
• System protection features:
   – Optional computer operating properly (COP) reset
   – Low-voltage detection with optional reset and selectable trip points for 3.3-V and 5.0-V operation
   – Illegal opcode detection with reset
   – Illegal address detection with reset
• Low-power design; fully static with stop and wait modes
• Standard low-power modes of operation:
   – Wait mode
   – Stop mode
• Master reset pin and power-on reset (POR)
• On-chip FLASH memory:
   – MC68HC908GZ60 — 60 Kbytes
   – MC68HC908GZ48 — 48 Kbytes
   – MC68HC908GZ32 — 32 Kbytes
• Random-access memory (RAM):
   – MC68HC908GZ60 — 2048 bytes
   – MC68HC908GZ48 — 1536 bytes
   – MC68HC908GZ32 — 1536 bytes
• Serial peripheral interface (SPI) module
• Enhanced serial communications interface (ESCI) module
• One 16-bit, 2-channel timer interface module (TIM1) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel
• One 16-bit, 6-channel timer interface module (TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel
• Timebase module with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external crystal
• 24-channel, 10-bit successive approximation analog-to-digital converter (ADC)
• 8-bit keyboard wakeup port with software selectable rising or falling edge detect, as well as high or low level detection
• Up to 53 general-purpose input/output (I/O) pins, including:
   – 40 shared-function I/O pins, depending on package choice
   – Up to 13 dedicated I/O pins, depending on package choice
• Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis. During output mode, pullups are disengaged.
• Internal pullups on IRQ and RST to reduce customer system cost
• High current 10-mA sink/source capability on all port pins
• Higher current 20-mA sink/source capability on PTC0–PTC4 and PTF0–PTF3
• User selectable clockout feature with divide by 1, 2, and 4 of the bus or crystal frequency
• User selection of having the oscillator enabled or disabled during stop mode
• BREAK module (BRK) to allow single breakpoint setting during in-circuit debugging
• Available packages:
   – 32-pin low-profile quad flat pack (LQFP)
   – 48-pin low-profile quad flat pack (LQFP)
   – 64-pin quad flat pack (QFP)
• Specific features in 32-pin LQFP are:
   – Port A is only 4 bits: PTA0–PTA3; shared with ADC and KBI modules
   – Port B is only 6 bits: PTB0–PTB5; shared with ADC module
   – Port C is only 2 bits: PTC0–PTC1; shared with MSCAN module
   – Port D is only 7 bits: PTD0–PTD6; shared with SPI, TIM1 and TIM2 modules
   – Port E is only 2 bits: PTE0–PTE1; shared with ESCI module
• Specific features in 48-pin LQFP are:
   – Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
   – Port B is 8 bits: PTB0–PTB7; shared with ADC module
   – Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
   – Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, and TIM2 modules
   – Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
• Specific features in 64-pin QFP are:
   – Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
   – Port B is 8 bits: PTB0–PTB7; shared with ADC module
   – Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
   – Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, andTIM2 modules
   – Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
   – Port F is 8 bits: PTF0–PTF7; shared with TIM2 module
   – Port G is 8 bits; PTG0–PTG7; shared with ADC module