Description
The AT91SAM9263 32-bit microcontroller, based on the ARM926EJ-S processor, is architectured on a 9-layer matrix, allowing a maximum internal bandwidth of nine 32-bit buses. It also features two independent external memory buses, EBI0 and EBI1, capable of interfacing with a wide range of memory devices and an IDE hard disk. Two external buses prevent bottlenecks, thus guaranteeing maximum performance.

FEATUREs
• Incorporates the ARM926EJ-S™ ARM® Thumb® Processor
    – DSP Instruction Extensions, Jazelle® Technology for Java® Acceleration
    – 16 Kbyte Data Cache, 16 Kbyte Instruction Cache, Write Buffer
    – 220 MIPS at 200 MHz
    – Memory Management Unit
    – EmbeddedICE™, Debug Communication Channel Support
    – Mid-level Implementation Embedded Trace Macrocell™
• Bus Matrix
    – Nine 32-bit-layer Matrix, Allowing a Total of 28.8 Gbps of On-chip Bus Bandwidth
    – Boot Mode Select Option, Remap Command
• Embedded Memories
    – One 128 Kbyte Internal ROM, Single-cycle Access at Maximum Bus Matrix Speed
    – One 80 Kbyte Internal SRAM, Single-cycle Access at Maximum Processor or Bus Matrix Speed
    – One 16 Kbyte Internal SRAM, Single-cycle Access at Maximum Bus Matrix Speed
• Dual External Bus Interface (EBI0 and EBI1)
    – EBI0 Supports SDRAM, Static Memory, ECC-enabled NAND Flash and CompactFlash®
    – EBI1 Supports SDRAM, Static Memory and ECC-enabled NAND Flash
• DMA Controller (DMAC)
    – Acts as one Bus Matrix Master
    – Embeds 2 Unidirectional Channels with Programmable Priority, Address Generation, Channel Buffering and Control
• Twenty Peripheral DMA Controller Channels (PDC)
• LCD Controller
    – Supports Passive or Active Displays
    – Up to 24 bits per Pixel in TFT Mode, Up to 16 bits per Pixel in STN Color Mode
    – Up to 16M Colors in TFT Mode, Resolution Up to 2048x2048, Supports Virtual Screen Buffers
• Two D Graphics Accelerator
    – Line Draw, Block Transfer, Clipping, Commands Queuing
• Image Sensor Interface
    – ITU-R BT. 601/656 External Interface, Programmable Frame Capture Rate
    – 12-bit Data Interface for Support of High Sensibility Sensors
    – SAV and EAV Synchronization, Preview Path with Scaler, YCbCr Format
• USB 2.0 Full Speed (12 Mbits per second) Host Double Port
    – Dual On-chip Transceivers
    – Integrated FIFOs and Dedicated DMA Channels
• USB 2.0 Full Speed (12 Mbits per second) Device Port
    – On-chip Transceiver, 2,432-byte Configurable Integrated DPRAM
• Ethernet MAC 10/100 Base-T
    – Media Independent Interface or Reduced Media Independent Interface
    – 28-byte FIFOs and Dedicated DMA Channels for Receive and Transmit
• Fully-featured System Controller, including
    – Reset Controller, Shutdown Controller
    – Twenty 32-bit Battery Backup Registers for a Total of 80 Bytes
    – Clock Generator and Power Management Controller
    – Advanced Interrupt Controller and Debug Unit
    – Periodic Interval Timer, Watchdog Timer and Double Real-time Timer
• Reset Controller (RSTC)
    – Based on Two Power-on Reset Cells, Reset Source Identification and Reset Output Control
• Shutdown Controller (SHDWC)
    – Programmable Shutdown Pin Control and Wake-up Circuitry
• Clock Generator (CKGR)
    – 32768Hz Low-power Oscillator on Battery Backup Power Supply, Providing a Permanent Slow Clock
    – 3 to 20 MHz On-chip Oscillator and Two Up to 240 MHz PLLs
(Continue ...)