HI1-0506A-8(1999) 데이터 시트보기 (PDF) - Intersil

부품명

상세내역

일치하는 목록

HI1-0506A-8
(Rev.:1999)

16-Channel, 8-Channel, Differential 8-Channel and Differential 4-Channel, CMOS Analog MUXs with Active Overvoltage Protection

Intersil 

HI-506A, HI-507A, HI-508A, HI-509A

Electrical Specifications Supplies = +15V, -15V; VREF Pin = Open; VAH (Logic Level High) = 4V; VAL (Logic Level Low) = 0.8V,

Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section (Continued)

PARAMETER

TEST

TEMP

-2, -8

-5, -7

CONDITIONS (oC)

MIN TYP MAX MIN TYP MAX UNITS

MOS Drive, VAL, HI-506A/HI-507A

VREF = +10V

25

-

-

0.8

-

-

0.8

V

MOS Drive, VAH, HI-506A/HI-507A

VREF = +10V

25

6.0

-

-

6.0

-

-

V

ANALOG CHANNEL CHARACTERISTICS

Analog Signal Range, VIN

On Resistance, rON

Note 2

Notes 2, 3

Full

-15

-

+15 -15

-

+15

V

25

-

1.2

1.5

-

1.5

1.8

kΩ

Full

-

1.5

1.8

-

1.8

2.0

kΩ

Off Input Leakage Current, IS(OFF)

Notes 2, 4

25

-

0.03

-

-

0.03

-

nA

Full

-

-

50

-

-

50

nA

Off Output Leakage Current, ID(OFF)

HI-506A

Notes 2, 4

25

-

0.1

-

-

0.1

-

nA

Full

-

-

300

-

-

300

nA

HI-507A

Full

-

-

200

-

-

200

nA

HI-508A

Full

-

-

200

-

-

200

nA

HI-509A

Full

-

-

100

-

-

100

nA

ID(OFF) With Input Overvoltage Applied

Note 5

25

-

4.0

-

-

4.0

-

nA

Full

-

-

2.0

-

-

-

µA

On Channel Leakage Current, ID(ON)

HI-506A

Notes 2, 4

25

-

0.1

-

-

0.1

-

nA

Full

-

-

300

-

-

300

nA

HI-507A

Full

-

-

200

-

-

200

nA

HI-508A

Full

-

-

200

-

-

200

nA

HI-509A

Full

-

-

100

-

-

100

nA

Differential Off Output Leakage Current, IDIFF,

(HI-507A, HI-509A Only)

Full

-

-

50

-

-

50

nA

POWER SUPPLY CHARACTERISTICS

Current, I+

Notes 2, 8

Full

-

0.5

2.0

-

0.5

2.0

mA

Current, I-

Notes 2, 8

Full

-

0.02 1.0

-

0.02 1.0

mA

Power Dissipation, PD

Full

-

7.5

-

-

7.5

-

mW

NOTES:

2. 100% tested for Dash 8. Leakage currents not tested at -55oC.

3. VOUT = ±10V, IOUT = +100µA.

4. 10nA is the practical lower limit for high speed measurement in the production test environment.

5. Analog Overvoltage = ±33V.

6. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at 25oC.

7. VEN = 0.8V, RL = 1K, CL = 15pF, VS = 7VRMS, f = 100kHz.

8. VEN, VA = 0V or 4V.

9. To drive from DTL/TTL Circuits, 1kΩ pull-up resistors to +5V supply are recommended.

8

Share Link: