P1014AP 데이터 시트보기 (PDF) - ON Semiconductor

부품명

상세내역

일치하는 목록

P1014AP

Self-Supplied Monolithic Switcher for Low Standby Power Offline SMPS

ON Semiconductor 

NCP1010, NCP1011,

NCP1012, NCP1013,

NCP1014

Self-Supplied Monolithic

Switcher for Low Standby-

Power Offline SMPS

The NCP101X series integrates a fixed−frequency current−mode

controller and a 700 V MOSFET. Housed in a PDIP−7 or SOT−223

package, the NCP101X offers everything needed to build a rugged and

low−cost power supply, including soft−start, frequency jittering,

short−circuit protection, skip−cycle, a maximum peak current setpoint

and a Dynamic Self−Supply (no need for an auxiliary winding).

Unlike other monolithic solutions, the NCP101X is quiet by nature:

during nominal load operation, the part switches at one of the available

frequencies (65 − 100 − 130 kHz). When the current setpoint falls

below a given value, e.g. the output power demand diminishes, the IC

automatically enters the so−called skip−cycle mode and provides

excellent efficiency at light loads. Because this occurs at typically 1/4

of the maximum peak value, no acoustic noise takes place. As a result,

standby power is reduced to the minimum without acoustic noise

generation.

Short−circuit detection takes place when the feedback signal fades

away, e.g. in true short−circuit conditions or in broken Optocoupler

cases. External disabling is easily done either simply by pulling the

feedback pin down or latching it to ground through an inexpensive

SCR for complete latched−off. Finally soft−start and frequency

jittering further ease the designer task to quickly develop low−cost and

robust offline power supplies.

For improved standby performance, the connection of an auxiliary

winding stops the DSS operation and helps to consume less than

100 mW at high line. In this mode, a built−in latched overvoltage

protection prevents from lethal voltage runaways in case the

Optocoupler would brake. These devices are available in economical

8−pin dual−in−line and 4−pin SOT−223 packages.

http://onsemi.com

MARKING

DIAGRAMS

4

4

SOT−223

CASE 318E

1

ST SUFFIX

AYW

101xy G

G

1

8

1

PDIP−7

CASE 626A

AP SUFFIX

P101xAPyy

AWL

YYWWG

1

x

= Current Limit (0, 1, 2, 3, 4)

y

= Oscillator Frequency

A (65 kHz), B (100 kHz), C (130 kHz)

yy

= 06 (65 kHz), 10 (100 kHz), 13 (130 kHz)

A

= Assembly Location

WL = Wafer Lot

YY, Y = Year

WW, W = Work Week

G or G = Pb−Free Package

(Note: Microdot may be in either location)

ORDERING INFORMATION

See detailed ordering and shipping information in the package

dimensions section on page 21 of this data sheet.

Features

• Built−in 700 V MOSFET with Typical RDSon of 11 W

and 22 W

• Large Creepage Distance Between High−Voltage Pins

• Current−Mode Fixed Frequency Operation:

65 kHz – 100 kHz − 130 kHz

• Skip−Cycle Operation at Low Peak Currents Only:

No Acoustic Noise!

• Dynamic Self−Supply, No Need for an Auxiliary

Winding

• Internal 1.0 ms Soft−Start

• Latched Overvoltage Protection with Auxiliary

Winding Operation

• Frequency Jittering for Better EMI Signature

• Auto−Recovery Internal Output Short−Circuit

Protection

• Below 100 mW Standby Power if Auxiliary Winding

is Used

• Internal Temperature Shutdown

• Direct Optocoupler Connection

• SPICE Models Available for TRANsient Analysis

• These are Pb−Free and Halide−Free Devices

Typical Applications

• Low Power AC/DC Adapters for Chargers

• Auxiliary Power Supplies (USB, Appliances,TVs, etc.)

© Semiconductor Components Industries, LLC, 2014

1

September, 2014 − Rev. 23

Publication Order Number:

NCP1010/D

Share Link: