PS394 데이터 시트보기 (PDF) - Pericom Semiconductor
부품명
상세내역
일치하는 목록
PS394 Datasheet PDF : 8 Pages
| |||
PS394
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900P1122r33e4455c66i77s88i99o0011n22,1122Q3344u5566a77d8899,00S1122P3344D5566T7788,9910011722V334455A6677n8899a00l11o2211g2233S4455w6677i88t99c00h1122
Electrical Characteristics Single +3.3V Supply
(V+ = 3.0V to 3.6V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
Parameter
Symbol
Conditions
Temp.
Range
Min.(2)
Switch
Analog Signal Range
On-Resistance
NC or NO Off
Leakage Current(8)
COM Leakage
Current(8)
VCOM,
VNO, VNC
(note 3)
V+ = 3V, V = 0V,
RON
VNC or VNO = 1.5V,
ICOM = 1.0mA, VINH = 2.4V,
VINL = 0.8V
INC(OFF)
or
INO(OFF)
VCOM = 0V,
VNC or VNO = 3V,
V+ = 3.6V, V = 0V
ICOM(ON)
VCOM = 3V,
VNC or VNO = 3V,
V+ = 3.6V, V = 0V
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
0V
C, E
C, E
C, E 0.2
C, E 2.5
C, E 0.4
C, E 5.0
Digital Logic Input
Input Current with
Input Voltage High
IINH
VIN = 2.4V, all others = 0.8V
1.0
Input Current with
Input Voltage Low
IINL
VIN = 0.8V, all others = 2.4V
1.0
Dynamic
Typ.(2) Max.(2)
V+
75
185
250
0.01 0.2
2.5
0.04
0.4
5.0
0.005 1.0
0.005 1.0
Units
V
Ohm
nA
µA
Turn-On-Time(3)
tON
VCOM = 1.5V, Figure 2
TA = +25°C
400
Turn-off-Time(3)
tOFF
VCOM = 1.5V, Figure 2
TA = +25°C
150
ns
Break-Before-Make
Time Delay (3)
Charge Injection (3)
Supply
Power-Supply Range
Positive Supply
Current
Negative Supply
Current
tD
VCTE
Figure 5
CL = 1.0nF, VGEN = 0V,
RGEN = 0 Ohm Figure 6
TA = +25°C
TA = +25°C
V+
I+
All channels on or off, VIN = 0V or V+, V+ = 3.6V, V = 0V
I
All channels on or off, VIN = 0V or V+, V+ = 3.6V, V = 0V
5
20
1
5
pC
2.7
16
V
1.0 0.01
1.0
µA
1.0 0.01 1.0
Notes:
2. The algebraic covention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet.
3. Guaranteed by design
4. ∆RON = ∆RON(MAX). On-resistance match between channels and flatness are guaranteed only with specified voltages. Flatness is defined as the
difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range.
5. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temperature.
6. See Figure 6. Off isolation = 20log10 VCOM/VNC or VNO, VCOM = output, VNC or NO = input to off switch
7. Between any two switches. See Figure 3.
8. Leakage testing at single supply is guaranteed by testing with dual supplies.
6
PS8444 01/13/00
Share Link: 