NCP348 데이터 시트보기 (PDF) - ON Semiconductor

부품명

상세내역

일치하는 목록

NCP348

Positive Overvoltage Protection Controller with Internal Low RON NMOS FET and Status FLAG

ON Semiconductor 

NCP348, NCP348AE

Undervoltage Lockout (UVLO)

To ensure proper operation under any conditions, the

device has a built−in undervoltage lockout (UVLO) circuit.

During Vin positive going slope, the output remains

disconnected from input until Vin voltage is below 3.25 V

(NCP348MTT version), plus hysteresis, nominal. The

FLAG output is tied to low as long as Vin does not reach

UVLO threshold. This circuit has a 50 mV hysteresis to

provide noise immunity to transient condition. Additional

UVLO thresholds ranging from UVLO can be

manufactured. (See Selection Guide on page 12) Contact

your ON Semiconductor representative for availability.

Overvoltage Lockout (OVLO)

To protect connected systems on Vout pin from

overvoltage, the device has a built−in overvoltage lockout

(OVLO) circuit. During overvoltage condition, the output

remains disabled as long as the input voltage exceeds 6.4 V

typical (NCP348MTT version). Additional OVLO

thresholds ranging from OVLO can be manufactured. (See

Selection Guide on page 12) Contact your ON

Semiconductor representative for availability.

FLAG output is tied to low until Vin is higher than OVLO.

This circuit has a 100 mV hysteresis to provide noise

immunity to transient conditions.

FLAG Output

The NCP348 provides a FLAG output, which alerts

external systems that a fault has occurred.

This pin is tied to low as soon the OVLO threshold is

exceeded or when the Vin level is below the UVLO

threshold. When Vin level recovers normal condition,

FLAG is held high, keeping in mind that an additional

50 ms delay has been added between available output and

FLAG = high. The pin is an open drain output, thus a pull

up resistor (typically 1 MW, minimum 10 kW) must be

added to Vbat. Minimum Vbat supply must be 2.5 V. The

FLAG level will always reflects Vin status, even if the

device is turned off (EN = 1).

EN Input

To enable normal operation, the EN pin shall be forced

to low or connected to ground. A high level on the pin,

disconnects OUT pin from IN pin. EN does not overdrive

an OVLO or UVLO fault.

Internal NMOS FET

The NCP348 includes an internal Low RDS(on) NMOS

FET to protect the systems, connected on OUT pin, from

positive overvoltage. Regarding electrical characteristics,

the RDS(on), during normal operation, will create low losses

on Vout pin.

As example: Rload = 8.0 W, Vin = 5.0 V

Typical RDS(on) = 65 mW, Iout = 618 mA

Vout = 8 x 0.618 = 4.95 V

NMOS losses = RDS(on) x Iout2 = 0.065 x 0.6182 = 25 mW

ESD Tests

The NCP348 input pin fully supports the IEC61000−4−2.

1.0 mF (minimum) must be connected between Vin and

GND, close to the device.

That means, in Air condition, Vin has a "15 kV ESD

protected input. In Contact condition, Vin has "8.0 kV

ESD protected input.

Please refer to Figure 19 to see the IEC 61000−4−2

electrostatic discharge waveform.

Figure 19. Electrostatic Discharge Waveform

PCB Recommendations

The NCP348 integrates a 2 amperes rated NMOS FET,

and the PCB rules must be respected to properly evacuate

the heat out of the silicon. The PAD1 is internally isolated

from the active silicon and should preferably be connected

to ground. The PAD2 of the NCP348 package is connected

to the internal NMOS drain and can be used to increase the

heat transfer if necessary from an applications standpoint.

Depending upon the power dissipated in the application,

one can either use the PCB tracks connected to Pins 4 and

5 to evacuate heat, or make profit of the PAD2 area to add

extra copper surface to reduce the junction temperature

(See Figure 20). Of course, in any case, this pad shall be not

connected to any other potential. Figure 20 shows copper

area according to RqJA and allows the design of the heat

transfer plane connected to PAD2.

http://onsemi.com

10

Share Link: