MSK4364(2011) 데이터 시트보기 (PDF) - M.S. Kennedy
부품명
상세내역
일치하는 목록
MSK4364 Datasheet PDF : 7 Pages
| |||
APPLICATION NOTES
MSK 4364 PIN DESCRIPTIONS
V+ - are the power connections from the hybrid to the bus.
All three pins for the motor voltage supply should be con-
nected together to share the current through the three pins in
the hybrid. The external wiring to these pins should be sized
according to the RMS current required by the motor. A high
quality monolithic ceramic capacitor for high frequencies and
enough bulk capacitance for keeping the V+ supply from
drooping should bypass these pins. 470μF is recommended.
Capacitors should be placed as close to these pins as practi-
cal.
AØ, BØ & CØ- are the connections to the motor phase wind-
ings from the bridge output. The wiring to these pins should
be sized according to the required current by the motor. There
are no short circuit provisions for these outputs. Shorts to
V+ or gound from these pins must be avoided or the bridge
will be destroyed. All three pins for each phase should be
connected together to share the current through the three
pins in the hybrid.
RTN - is the power return connection from the module to the
bus. All internal ground returns connect to this point inside
the hybrid. All three pins should be connected together to
share the current. All capacitors from the V+ bus should
connect to this point as close as possible. All external V+
return connections should be made as close to these pins as
possible. Wiring sizing to this pin should be made according
to the required current.
GND - is the return point for the low powered circuitry inside
the hybrid. All GND pins should be tied together. All capaci-
tors for bypassing the + and -15V supplies should be tied at
this point, as close to the pins as possible. Any ground plane
connections for low powered and analog citcuitry outside the
hybrid should be tied to this point.
+15VIN - is the input for applying +15 volts to run the low
power section of the hybrid. Both pins should be used to-
gether for optimum operation. These pins should be bypassed
with a 10μF capacitor and a 0.1μF capacitor as close to these
pins as possible.
-15VIN - is the input for applying -15 volts to run the low
power section of the hybrid. Both pins should be used to-
gether for optimum operation. These pins should be bypassed
with a 10μF capacitor and a 0.1μF capacitor as close to these
pins as possible.
REFOUT - is a 6.25 volt regulated output to be used for pow-
ering the hall devices in various motors. Up to 15mA of
output current is available.
HALL A,B,C - are the hall input pins from the hall devices in
the motor. These pins are internally pulled up to 6.25 volts.
The halls can reflect a 120/240 degree commutation or a 60/
300 degree scheme.
BRAKE - is a pin for commanding the output bridge into a
motor BRAKE mode. When pulled low, normal operation pro-
ceeds. When pulled high, the three high side bridge transis-
tors turn off and the three low side transistors turn fully on
without PWM'ing. This will cause rapid deceleration of the
motor and will cease motor operation until pulled high again.
Logic levels for this input are TTL compatible. It is internally
pulled to 6.25 volts.
60/120 - is a pin for selecting the orientation scheme of the
motor. A high state will produce 60/300 degree commuta-
tion, whereas a low state will produce 120/240 degree com-
mutation. Logic levels for this input are TTL compatible. It is
internally pulled to 6.25 volts.
CURRENT COMMAND (+) - is the input for controlling the
module in current mode. Scaled at 1 amp per volt of input
command, the bipolar input allows both forward and reverse
current control capability regardless of motor commutation
direction. The maximum operational command voltage should
be ±5 volts for ±5 amps of motor current. Going beyond 5
volts of command voltage will force the bridge to conduct
more than the desired maximum current. There is internal
IN current limiting that will ultimately limit the absolute maxi-
mum current being output by the bridge.
CURRENT MONITOR- is a pin providing a current viewing
signal for external monitoring purposes. This is scaled at ±1
amp of motor current per volt output, up to a maximum of
±5 volts, or ±5 amps. Going beyond the 5 volt maximum
may result in clipping of the waveform peaks. In DIS mode,
the CURRENT MONITOR output may rail positive or negative,
depending on internal bias currents. When re-enabled, this
output will resume expected operation.
E/A OUT - is the current loop error amplifier output. It is
brought out for allowing various loop compensation circuits
to be connected between this and E/A-.
E/A- - is the current loop error amplifier inverting input. It is
brought out for allowing various loop compensation circuits
to be connected between this and E/A OUT.
DIS - is a pin for externally disabling the output bridge. Shorted
to GND will enable the bridge and pulled to +15V with a 10K
resistor will disable it. It is not internally pulled up.
3
Rev. G 2/11
Share Link: 