DG508ACJZ 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
일치하는 목록
DG508ACJZ Datasheet PDF : 9 Pages
| |||
DG508A
Electrical Specifications TA = 25oC, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V, Unless Otherwise Specified (Continued)
“A” SUFFIX
“B” AND “C” SUFFIX
PARAMETER
TEST CONDITIONS
(NOTE 4) (NOTE 3) (NOTE 4) (NOTE 4) (NOTE 3) (NOTE 4)
MIN
TYP
MAX
MIN
TYP
MAX UNITS
Source OFF Leakage
Current, IS(OFF)
VEN = 0V
Drain OFF Leakage
Current, ID(OFF)
VEN = 0V
Drain ON Leakage Current, (Note 6)
ID(ON)
Sequence Each
Switch ON
VAL = 0.8V,
VAH = 2.4V
POWER SUPPLY CHARACTERISTICS
VS = +10V, VD = -10V
VS = -10V, VD = +10V
VS = -10V, VD = +10V
VS = +10V, VD = -10V
VD = VS(ALL) = +10V
VD = VS(ALL) = -10V
-1
0.002
1
-1
-0.005
1
-
0.01
10
-10
-0.015
-
-
0.015
10
-10
-0.03
-
-5
0.002
5
nA
-5
-0.005
5
nA
-
0.01
20
nA
-20 -0.015
-
nA
-
0.015
20
nA
-20
-0.03
-
nA
Positive Supply Current, I+ VEN = 5.0V (Enabled) or
Negative Supply Current, I- VEN = 0V (Standby), VA = 0V
-
1.3
2.4
-
1.3
2.4
mA
-1.5
-0.7
-
-1.5
-0.7
-
mA
Electrical Specifications TA = Over Operating Temperature Range, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
“A” SUFFIX
(NOTE 3)
MIN TYP MAX
UNITS
DIGITAL INPUT CHARACTERISTICS
Address Input Current, Input Voltage
High, IAH
VA = 2.4V
VA = 15V
Address Input Current Input Voltage
Low, IAL
VEN = 2.4V
VEN = 0V
ANALOG SWITCH CHARACTERISTICS
VA = 0V
-30
-
-
µA
-
-
30
µA
-30
-
-
µA
-30
-
-
µA
Analog Signal Range, VANALOG
(Note 7)
-15
-
+15
V
Drain-Source ON Resistance, rDS(ON) Sequence Each Switch ON
VAL = 0.8V, VAH = 2.4V
IS = -200µA, VD = +10V
-
IS = -200µA, VD = -10V
-
-
500
Ω
-
500
Ω
Source OFF Leakage Current, IS(OFF) VEN = 0V
VS = +10V, VD = -10V
-
-
50
nA
VS = -10V, VD = +10V
-50
-
-
nA
Drain OFF Leakage Current, ID(OFF) VEN = 0V
VS = -10V, VD = +10V
-
-
200
nA
VS = +10V, VD = -10V
-200
-
-
nA
Drain ON Leakage Current, ID(ON)
(Note 6) Sequence Each Switch ON VD = VS(ALL) = +10V
VAL = 0.8V, VAH = 2.4V
VD = VS(ALL) = -10V
-
-
-200
-
200
nA
-
nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
Negative Supply Current, I-
VEN = 5.0V, VA = 0V
-3.2
-
4.5
mA
-3.2
-
4.5
mA
Positive Standby Supply Current, I+
Negative Standby Supply Current, I-
VEN = 0V, VA = 0V
-3.2
-
4.5
mA
-3.2
-
4.5
mA
NOTES:
3. Typical values are for design aid only, not guaranteed and not subject to production testing.
4. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.
5. Off isolation = 20Log |VS|/|VD|, where VS = input to Off switch, and VD = output due to VS.
6. ID(ON) is leakage from driver into “ON” switch.
7. Parameter not tested. Parameter guaranteed by design or characterization.
4
Share Link: 