MC10EL15DG(2016) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
일치하는 목록
MC10EL15DG Datasheet PDF : 8 Pages
| |||
MC10EL15, MC100EL15
Table 8. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3)
25
35
25
35
25
38
mA
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
−1165
−880 −1165
−880 −1165
−880 mV
−1810
−1475 −1810
−1475 −1810
−1475 mV
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26 V
−2.5
−0.4 −2.5
−0.4 −2.5
−0.4 V
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50ĂW resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
Table 9. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC= 0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fMAX
tPLH
tPHL
Maximum Toggle Frequency
Propagation Delay
CLK to Q (Diff)
CLK to Q (SE)
SCLK to Q
1.25
GHz
460
660 470
670 500
700 ps
410
710 420
720 450
750
410
710 420
720 470
750
tSKEW
Part-to-Part Skew
Within-Device Skew (Note 2)
200
200
200 ps
50
50
50
tJITTER
tS
tH
VPP
tr
tf
Random Clock Jitter (RMS)
Setup Time EN
Hold Time EN
Input Swing (Note 3)
Output Rise/Fall Times Q
(20% − 80%)
2.6
ps
150
150
150
ps
400
400
400
ps
150
1000 150
1000 150
1000 mV
325
575 325
575 325
575 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary +0.06 V / −0.5 V.
100 Series: VEE can vary +0.8 V / −0.5 V.
2. Skews are specified for identical LOW-to-HIGH or HIGH-to-LOW transitions.
3. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈ 40.
www.onsemi.com
5
Share Link: 