MC10EL15DG(2016) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
일치하는 목록
MC10EL15DG Datasheet PDF : 8 Pages
| |||
MC10EL15, MC100EL15
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
Iout
Output Current
VEE = 0 V
VCC = 0 V
Continuous
Surge
8
V
−8
V
50
mA
100
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
VI ≤ VCC
VI ≥ VEE
SOIC−16
6
−6
± 0.5
−40 to +85
−65 to +150
130
75
V
mA
°C
°C
°C/W
qJC
Thermal Resistance (Junction-to-Case)
Tsol
Wave Solder (Pb-Free)
Standard Board
SOIC−16
<2 to 3 sec @ 260°C
33 to 36
265
°C/W
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 5. 10EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3)
25
35
25
35
25
35
mA
3920 4010 4110 4020 4105 4190 4090 4185 4280 mV
3050 3200 3350 3050 3210 3370 3050 3227 3405 mV
3770
4110 3870
4190 3940
4280 mV
3050
3500 3050
3520 3050
3555 mV
3.57
3.7 3.65
3.75 3.69
3.81 V
2.5
4.6 2.5
4.6 2.5
4.6
V
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.3
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.06 V / −0.5 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
www.onsemi.com
3
Share Link: 