HSP9520 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
일치하는 목록
HSP9520 Datasheet PDF : 4 Pages
| |||
HSP9520, HSP9521
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input or Output Voltage Applied . . . . . . . . . . GND -0.5 to VCC +0.5V
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4.75V to 5.25V
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
67
SOIC Package . . . . . . . . . . . . . . . . . . . 77.0
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
DC Electrical Specifications
PARAMETER
Logical One Input Voltage
Logical Zero Input Voltage
Output HIGH Voltage
Output LOW Voltage
Input Leakage Current
Output Leakage Current
Standby Power Supply Current
Operating Power Supply Current
Input Capacitance
Output Capacitance
VCC = 5.0V ±5%, TA = 0oC to 70oC
SYMBOL
TEST CONDITIONS
VIH
VIL
VOH
VOL
II
IO
ICCSB
ICCOP
VCC = 5.25V
VCC = 4.75V
IOH = -6.5mA, VCC - 4.75V
IOH = +20.0mA, VCC = 4.75V
VIN = VCC or GND, VCC = 5.25V
VOUT = VCC or GND, VCC = 5.25V
VIN = VCC or GND, VCC = 5.25V Outputs Open
f = 5.0MHz, VIN = VCC or GND, VCC = 5.25V, Outputs
Open (Note 2)
CIN FREQ = 1MHZ, VCC = Open, All Measurements are
Referenced to Device Ground
CO
MIN MAX UNITS
2.0
-
V
-
0.8
V
2.4
-
V
-
0.5
V
-10
-10
µA
-10
-10
µA
-
500
µA
-
12
mA
-
12
pF
-
12
pF
AC Electrical Specifications VCC = 5.0V ±5%, TA = 0oC to 70oC (Note 3)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN MAX UNITS
Clock to Data Out
tPD
-
21
ns
Mux Select to Data Out
tSELD
-
20
ns
Input Setup Time (DO-7/10-7)
tS
10
-
ns
Input Hold Time (DO-7/10-7)
tH
3
-
ns
Output Enable Time
tENA
-
20
ns
Output Disable Time
tDIS (Note 4)
-
13
ns
Clock Pulse Width
tPW
10
-
ns
NOTES:
2. Power supply current is proportional to frequency. Typical rating for ICCOP is 2.4mA/MHz.
3. AC Testing is performed as follows: Input levels: 0V and 3.0V, timing reference levels = 1.5V, input rise and fall times driven at 1ns/V, output
load CL = 40pF.
4. Controlled by design or process parameters and not directly tested. Characterized upon initial design and after major design and/or process
changes.
3
Share Link: 