A29400B 데이터 시트보기 (PDF) - AMIC Technology

부품명

상세내역

일치하는 목록

A29400B

512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory

AMIC Technology 

START

Embedded

Program

algorithm in

progress

Increment Address

Write Program

Command

Sequence

Data Poll

from System

Verify Data ?

No

Yes

Last Address ?

Yes

Programming

Completed

Note : See the appropriate Command Definitions table for

program command sequence.

Figure 2. Program Operation

Chip Erase Command Sequence

Chip erase is a six-bus-cycle operation. The chip erase

command sequence is initiated by writing two unlock cycles,

followed by a set-up command. Two additional unlock write

cycles are then followed by the chip erase command, which

in turn invokes the Embedded Erase algorithm. The device

does not require the system to preprogram prior to erase.

The Embedded Erase algorithm automatically preprograms

and verifies the entire memory for an all zero data pattern

prior to electrical erase. The system is not required to

provide any controls or timings during these operations. The

Command Definitions table shows the address and data

requirements for the chip erase command sequence.

Any commands written to the chip during the Embedded

Erase algorithm are ignored. The system can determine the

status of the erase operation by using I/O7, I/O6, or I/O2. See

"Write Operation Status" for information on these status bits.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are no

longer latched.

A29400B Series

Figure 3 illustrates the algorithm for the erase operation.

See the Erase/Program Operations tables in "AC

Characteristics" for parameters, and to the Chip/Sector

Erase Operation Timings for timing waveforms.

Sector Erase Command Sequence

Sector erase is a six-bus-cycle operation. The sector erase

command sequence is initiated by writing two unlock cycles,

followed by a set-up command. Two additional unlock write

cycles are then followed by the address of the sector to be

erased, and the sector erase command. The Command

Definitions table shows the address and data requirements

for the sector erase command sequence.

The device does not require the system to preprogram the

memory prior to erase. The Embedded Erase algorithm

automatically programs and verifies the sector for an all

zero data pattern prior to electrical erase. The system is not

required to provide any controls or timings during these

operations.

After the command sequence is written, a sector erase time-

out of 50μs begins. During the time-out period, additional

sector addresses and sector erase commands may be

written. Loading the sector erase buffer may be done in any

sequence, and the number of sectors may be from one

sector to all sectors. The time between these additional

cycles must be less than 50μs, otherwise the last address

and command might not be accepted, and erasure may

begin. It is recommended that processor interrupts be

disabled during this time to ensure all commands are

accepted. The interrupts can be re-enabled after the last

Sector Erase command is written. If the time between

additional sector erase commands can be assumed to be

less than 50μs, the system need not monitor I/O3. Any

command other than Sector Erase or Erase Suspend during

the time-out period resets the device to reading array data.

The system must rewrite the command sequence and any

additional sector addresses and commands.

The system can monitor I/O3 to determine if the sector erase

timer has timed out. (See the " I/O3: Sector Erase Timer"

section.) The time-out begins from the rising edge of the

final WE pulse in the command sequence.

Once the sector erase operation has begun, only the Erase

Suspend command is valid. All other commands are

ignored.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are no

longer latched. The system can determine the status of the

erase operation by using I/O7, I/O6, or I/O2. Refer to "Write

Operation Status" for information on these status bits.

Figure 3 illustrates the algorithm for the erase operation.

Refer to the Erase/Program Operations tables in the "AC

Characteristics" section for parameters, and to the Sector

Erase Operations Timing diagram for timing waveforms.

Erase Suspend/Erase Resume Commands

The Erase Suspend command allows the system to

interrupt a sector erase operation and then read data from,

or program data to, any sector not selected for erasure. This

command is valid only during the sector erase operation,

including the 50μs time-out period during the sector erase

command sequence. The Erase Suspend command is

ignored if written during the chip erase operation or

Embedded Program algorithm. Writing the Erase Suspend

command during the Sector Erase time-out immediately

PRELIMINARY (June, 2016, Version 0.0)

10

AMIC Technology, Corp.

Share Link: