HA5024 데이터 시트보기 (PDF) - Renesas Electronics
부품명
상세내역
일치하는 목록
HA5024 Datasheet PDF : 17 Pages
| |||
HA5024
Electrical Specifications
PARAMETER
VSUPPLY = 5V, RF = 1k AV = +1, RL = 400 CL 10pF,Unless Otherwise Specified (Continued)
TEST CONDITIONS
(NOTE 11)
TEST TEMP.
LEVEL
(°C)
MIN
TYP
MAX
UNITS
AC CHARACTERISTICS (AV = +2, RF = 681)
Slew Rate
Note 8
B
25
-
475
-
V/s
Full Power Bandwidth
Note 9
B
25
-
26
-
MHz
Rise Time
Note 10
B
25
-
6
-
ns
Fall Time
Note 10
B
25
-
6
-
ns
Propagation Delay
Note 10
B
25
-
6
-
ns
Overshoot
B
25
-
12
-
%
-3dB Bandwidth
Settling Time to 1%
VOUT = 100mV
2V Output Step
B
25
-
95
-
B
25
-
50
-
MHz
ns
Settling Time to 0.25%
2V Output Step
B
25
-
100
-
ns
Gain Flatness
5MHz
B
25
-
0.02
-
dB
20MHz
B
25
-
0.07
-
dB
AC CHARACTERISTICS (AV = +10, RF = 383)
Slew Rate
Note 8
B
25
350
475
-
V/s
Full Power Bandwidth
Note 9
B
25
28
38
-
MHz
Rise Time
Note 10
B
25
-
8
-
ns
Fall Time
Note 10
B
25
-
9
-
ns
Propagation Delay
Note 10
B
25
-
9
-
ns
Overshoot
B
25
-
1.8
-
%
-3dB Bandwidth
Settling Time to 1%
VOUT = 100mV
2V Output Step
B
25
-
65
-
B
25
-
75
-
MHz
ns
Settling Time to 0.1%
2V Output Step
B
25
-
130
-
ns
VIDEO CHARACTERISTICS
Differential Gain (Note 15)
RL = 150
B
25
-
0.03
-
%
Differential Phase (Note 15)
RL = 150
B
25
-
0.03
-
Degrees
NOTES:
5. VCM = 2.5V. At -40°C Product is tested at VCM = 2.25V because short test duration does not allow self heating.
6. RL = 100, VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV VOUT +10mV.
7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5024 remaining enabled. The HA5024 is
considered disabled when the supply current has decreased by at least 0.5mA.
8. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
9. FPBW = 2-S----l--e-V--w--P----R-E---a-A---t-e-K-- ; VPEAK = 2V .
10. RL = 100, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.
12. VIN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to VOUT = 0V.
13. VIN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to VOUT = 2V.
14. VIN = 0V, Force VOUT from 0V to 2.5V, tR = tF = 50ns, DISABLE = 0V.
15. Measured with a VM700A video tester using an NTC-7 composite VITS.
16. VOUT = 2.5V. At -40°C Product is tested at VOUT = 2.25V because short test duration does not allow self heating.
FN3550 Rev 6.00
February 8, 2006
Page 4 of 17
Share Link: 