PI74FCT162344T 데이터 시트보기 (PDF) - Pericom Semiconductor
부품명
상세내역
일치하는 목록
PI74FCT162344T Datasheet PDF : 6 Pages
| |||
PI74FCT162344T
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234A567d8d90r12e3s4s5/6C789lo01c2k123D45r67iv89e0r12
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ......................................................... –65°C to +150°C
Note:
Stresses greater than those listed under
Ambient Temperature with Power Applied ....................... 0°C to +70°C
MAXIMUM RATINGS may cause permanent damage
Supply Voltage to Ground Potential ................................. –0.5V to +7.0V
DC Input Voltage .............................................................. –0.5V to +7.0V
to the device. This is a stress rating only and functional
operation of the device at these or any other conditions
above those indicated in the operational sections of
DC Output Current ............................................................ –60 to +120 mA
Power Dissipation .............................................................. 0.5W
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
Operating Range
Ambient Temperature = –40°C to +85°C
Vcc = 5.0V ±10%
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ±10%)
Parameters Description
Test Conditions(1)
Min. Typ(2) Max.
VOH
Output HIGH Voltage VCC = Min, VIN = VIH or VIL
IOH = – 24mA
2.4 3.3 —
VOL
Output LOW Voltage VCC = Min., VIN = VIH or VIL
IOL = 24mA
— 0.3 0.55
VIH
Input HIGH Voltage Guaranteed Logic HIGH Level
2.0 — —
VIL
Input LOW Voltage Guaranteed Logic LOW Level
— — 0.8
IIH
Input HIGH Current VCC = Max.
VIN = VCC (Input Pins)
— — ±1
IIL
Input LOW Current VCC = Max.
VIN = GND (Input & I/O Pins)
— — ±1
IOZH
High Impedance
VCC = Max.
VOUT = 2.7V
— — ±1
IOZL
Output Current
(3-State Output Pins)
VOUT = 0.5V
— — ±1
VIK
Clamp Diode Voltage VCC = Min., IIN = –18mA
IODH
Output HIGH Current VCC = 5V, VIN =VIH or VIL, VOUT = 1.5V(3)
IODL
Output LOW Current VCC = 5V, VIN =VIH or VIL, VOUT = 1.5V(3)
— –0.7 –1.2
–60 –115 –150
60 115 150
IOS
Short Circuit Current(4) VCC = Max., VOUT = GND(4)
–80 –140 –225
IOUT
Output Drive Current VCC = Max., VOUT = 2.5V(3)
–50 — –180
VH
Input Hysteresis
— 100 —
Units
V
V
V
V
µA
µA
µA
V
mA
mA
mA
mA
mV
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. This parameter is determined by device characterization but is not production tested.
4. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
3
PS2047B 03/22/99
Share Link: 