AD7641BCPZ 데이터 시트보기 (PDF) - Analog Devices
부품명
상세내역
일치하는 목록
AD7641BCPZ Datasheet PDF : 14 Pages
| |||
AD7631/AD7634
Preliminary Technical Data
Pin
No.
11, 12
13
14
15
16
17
18
19
20
21
22
23
Mnemonic
D[4:5]
or DIVSCLK[0:1]
D6
or EXT/INT
D7
or INVSYNC
D8
or INVSCLK
D9
or RDC
or SDIN
OGND
OVDD
DVDD
DGND
D10
or SDOUT
D11
or SCLK
D12
or SYNC
Type 1
DI/O
DI/O
DI/O
DI/O
DI/O
P
P
P
P
DO
DI/O
DO
Description
When MODE[1:0] = 0, 1, or 2, these pins are Bit 4 and Bit 5 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock division selection. When using serial master read
after convert mode (EXT/INT = low, RDC/SDIN = low), these inputs can be used to slow down the
internally generated serial clock that clocks the data output. In other serial modes, these pins are
high impedance outputs.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 6 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock source select. This input is used to select the
internally generated (master) or external (slave) serial data clock.
When EXT/INT = low, master mode. The internal serial clock is selected on SCLK output.
When EXT/INT = high, slave mode. The output data is synchronized to an external clock signal,
gated by CS, connected to the SCLK input.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 7 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), invert sync select. In serial master mode (EXT/INT = low), this
input is used to select the active state of the SYNC signal.
When INVSYNC = low, SYNC is active high.
When INVSYNC = high, SYNC is active low.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 8 of the parallel port data output bus.
When MODE[1:0] = 3, invert SCLK select. In all serial modes, this input is used to
invert the SCLK signal.
When MODE[1:0] = 0, 1, or 2, this output is used as bit 9 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), read during convert. When using serial master mode
(EXT/INT = low), RDC is used to select the read mode.
When RDC = high, the previous conversion result is output on SDOUT during conversion and
the period of SCLK changes.
When RDC = low (read after convert), the current result can be output on SDOUT only when
the conversion is complete.
When MODE[1:0] = 3 (serial mode), serial data in. When using serial slave mode, (EXT/INT = high),
SDIN could be used as a data input to daisy-chain the conversion results from two or more ADCs
onto a single SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 18 SCLK
periods after the initiation of the read sequence.
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the
host interface (2.7 V to 5V).
Digital Power. Nominally at 5 V.
Digital Power Ground.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 10 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial data output. In serial mode, this pin is used as the serial
data output synchronized to SCLK. Conversion results are stored in an on-chip register. The ADC
provides the conversion result, MSB first, from its internal shift register. The data format is
determined by the logic level of OB/2C.
In master mode, EXT/INT = low. SDOUT is valid on both edges of SCLK.
In slave mode, EXT/INT = high:
When INVSCLK = low, SDOUT is updated on SCLK rising edge and valid on the next falling edge.
When INVSCLK = high, SDOUT is updated on SCLK falling edge and valid on the next rising edge.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 11 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock. In all serial modes, this pin is used as the serial
data clock input or output, depending upon the logic state of the EXT/INT pin. The active edge
where the data SDOUT is updated depends on the logic state of the INVSCLK pin.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 12 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), frame synchronization. In serial master mode (EXT/INT= low),
this output is used as a digital output frame synchronization for use with the internal data clock.
Rev. PrC | Page 10 of 14
Share Link: 