3560 데이터 시트보기 (PDF) - Unspecified

부품명

상세내역

일치하는 목록

3560

AC mΩ HiTESTER

Unspecified 

2

High-Speed Measurement Contributing to

Super Efficient Production Lines

■ Designed for System Use

Utilize the built-in external control terminal to select the

comparator table, as trigger and for requesting printout, etc.

The external output can be used for output of comparator

results, measurement completion (EOC) and NG output. These

external input and output capabilities have been designed with

systems integration in mind.

Power button

Built-in RS-232C

Timing Chart Example

The following shows a timing example for reading out the

comparator results using the HOLD function and external

input and output features.

t1: Approx. 80 ms (FAST 60 Hz), approx. 660 ms (MEDIUM 60 Hz), approx. 1.6s (SLOW 60 Hz)

Approx. 95 ms (FAST 50 Hz), approx. 795 ms (MEDIUM 50 Hz), approx. 1.92s (SLOW 50 Hz)

t2: Approx. 5 ms

t3: Approx. 1 ms

In the HOLD mode, the sequence is simple as EOC is retained until the next

trigger is input. Furthermore, the display and output are retained until the

next EOC is entered.

t1: [Stabilizing time] Following chuck, the trigger is input after the

measuring current has stabilized.

t2: [Detection time] Time from when chuck is detected until the NG

signal becomes Lo.

* t1 and t2 differ with the measured object. The figures are reference values in case

of pure resistance.

t3: [Evaluation time] The time from when the measurement value is

judged at the point when the trigger is input and until

the EOC signal is output. The comparison result is

decided on the rising edge of EOC. At this point, the

evaluation result is obtained.

External control terminal

External output terminal

GP-IB or printer interface

Nature of external control and outputs (negative logic)

● Control

(CMOS/5 V max.)

• Measurement trigger (TRIG)

• Comparator output request (MANU)

• Zero adjustment request (0 ADJ)

• Print request (PRINT)

• Comparator table selection (COMP)

• EXT.DCV (DC5V - 24V)

• GND

● Output

(Open-collector output/35V - 50mA max.)

• Comparator result signals (Hi, IN,

Lo/PASS, FAIL)

• Measurement termination signal

(EOC)

• Measurement irregularity detection

signal (NG)

Switch between automatic and manual output of comparator results

(set using panel buttons)

In the AUTO mode, the comparator results are continuously output. In the MANU mode,

the results are only output when the external MANU and GND terminals are shortened.

● MANU mode

RS-232C Interface Specifications

Transmission method: Start-stop synchronization, full duplex.

Transmission speed: 9600 bps. Data length: 8 bits. Parity: None. Stop

bit: 1 bit. Handshake: Hardware. Delimiter: CR+LF. Connecting cable:

D-Sub 9-pin female/female connector. Reverse connection.

■ External Interfaces (Options)

Install the optional 9588 GP-IB interface to gain full remote

control of the instrument from a PC. Add the 9589 Printer

Interface to enhance the device with printing capabilities via

the 9203 Digital Printer or your own Centronics-based printer.

Connecting the 9203 provides multi-function printing, such

as interval printing, statistical processing of maxima, minima,

average, standard deviation, histogram and graph printing.

9588 GP-IB Interface Specifications

Conforming standard: IEEE-488.1 1987/Reference standard: IEEE-488.2 1987

9203 Digital Printer Specifications

● Printer type: Thermal Line Printer

● Statistical processing: Up to 99,999

data points

● Histogram and graphics: Up to 5,000

data points

● Dimensions and mass: Approx. 215

(W)×160 (H)×54 (D)mm ,1kg / [8.5" (W)

× 6.3" (H) × 2.1" (D) , 35.3 oz.]

*Note: For further details, please refer to

the product catalog for the HIOKI

3550 Battery HiTESTER series, or

click onto our website at http://

www.hioki.co.jp.

Print example

Statistical processing

Resistance value histogram

Resistance value graph printout

Share Link: