NC1V-3513-7AS 데이터 시트보기 (PDF) - Unspecified

부품명

상세내역

일치하는 목록

NC1V-3513-7AS

NC1V Circuit Protectors

Unspecified 

NC1V Circuit Protectors

• 3-pole

47.0

6.6

M5 Terminal Screw (30A)

66.0

48.3

DIN Rail (BNDN1000)

All dimensions in mm.

Mounting Hole Layout

(M4 Mounting Screws)

47.0

NC1V-3500

(Relay Trip)

ON

M3.5 Terminal Screw

2-ø4.5 Holes

(for screw mounting)

52.5

Terminal Cover

5.0

33.0

2-M4

Instructions

• Installation Angle

Tripping method is hydraulic magnetic. Minimum operating

current varies with installation angle. Operating currents

are influenced by the weight of movable iron core. With

reference to the following figures, correct the rated current.

100%

120%

90%

100%

Minimum operating current is calculated from the following

formula:

(Minimum operating current) = (Rated current) ×

(Correction factor by installation angle) × (Reference

minimum tripping current rate)

• DIN Rails

[Installation on DIN Rail]

1. Fasten the DIN rail securely.

2. With the latch facing downward, install the NC1V circuit

protector on the DIN rail as shown below.

[Removal from DIN Rail]

Using a flat screwdriver, pull the latch on the circuit

protector to remove from the DIN rail.

Installing

35mm-wide

DIN Rail

Removing

35mm-wide

DIN Rail

Push

Flat

Srcrewdriver

Latch

• Applicable Wire and Crimp Terminal

Terminal

Terminal Screw

Connectable Applicable

Wire Size Crimping

(mm2)

Terminal

Spring-up, fingersafe,

slotted Phillips screw

with square washer

(up to 20A)

0.25 to 1.65

1.04 to 2.63

2.63 to 6.64

R1.25-4

R2-4

R5.5-4

Spring-up fingersafe

terminal

(25A and 30A)

0.25 to 1.65

1.04 to 2.63

2.63 to 6.64

R1.25-5

R2-5

R5.5-5

Tightening

Torque

(N·m)

1 to 1.4

1.8 to 2.2

Slotted Phillips screw

with square washer

0.25 to 1.65

1.04 to 2.63

R1.25-3.5

R2-3.5

0.7 to 0.9

• For wiring the main circuit terminal, use the applicable crimp terminals and

tighten to the recommended torque.

• When using the NC1V circuit protector as CSA-certified product, use with CSA-

certified crimp terminal.

• When using the NC1V circuit protector as UL-listed product, use with UL-listed

crimp terminal.

Panel Mounting Screw (not supplied)

Srew Type

Tightening Torque

Shape

Spring Washer

M4

0.8 to 1.0 N·m

Plain Washer

Product Markings (Example: NC1V-1111-30AA)

Type No.

Rated Voltage

Rated Current

PSE Certification

PS

E

JET

220VAC 30A I.C.2500A

CIRCUIT PROTECTOR

NC1V-1111

POLE 1

Ue 250VAC 50/60Hz · 65VDC

In 30A

CURVE A

Suppl. Prot.

AUX. SW

125VAC 3A

30 VDC 2A

A.T. 40°C

JAPAN

No. of Poles

Time Delay Curve

Auxiliary/Alarm Contact Rating

Reference Operating

Temperature

Certification Marks

Installation of Auxiliary/Alarm Terminal Cover

After wiring the terminals, install the terminal cover by

aligning with the circuit protector as shown below.

Terminal cover installed

11

Share Link: