NTE1509 데이터 시트보기 (PDF) - NTE Electronics
부품명
상세내역
일치하는 목록
NTE1509 Datasheet PDF : 4 Pages
| |||
Electrical Characteristics (Cont’d): (Note 2, unless otherwise specified, all specifications apply
with the following conditions:
3VDC ≤ V+ ≤ 20VDC
3VDC ≤ VLED ≤ V+
–0.015V ≤ VRLO ≤ 12VDC
–0.015V ≤ VRHI ≤ 12VDC
VREF, VRHI, VRLO ≤ (V+ –1.5V)
0V ≤ VIN ≤ V+ –1.5V
TA +25°C, IL(REF) = 0.2mA,
VLED = 3V, Pin9 connected to Pin3
(Bar Mode)
Parameter
Test Conditions
Min Typ Max Unit
Output Drivers
LED Current
LED Current Difference (Between Largest
and Smallest LED Currents)
LED Current Regulation
Dropout Voltage
Saturation Voltage
Output Leakage, Each Collector
V+ = VLED = 5V, IL(REF) = 1mA
VLED = 5V
ILED = 2mA
ILED = 20mA
2V ≤ VLED ≤ 17V ILED = 2mA
ILED = 20mA
ILED(ON) = 20mA, VLED = 5V,
∆ILED = 2mA
ILED = 2mA, IL(REF) = 0.4mA
Bar Mode, Note 4
7 10 13 mA
– 0.12 0.4 mA
– 1.2 3.0 mA
– 0.1 0.25 mA
–13
mA
– – 1.5
V
– 0.15 0.4
V
– 0.1 10
µA
Output Leakage
Dot Mode, Note 4 Pin10 to Pin18
– 0.1 10
µA
Pin1
60 150 450 µA
Supply Current
Standby Supply Current (All Outputs OFF)
V+ = 5V, IL(REF) = 0.2mA
V+ = 20V, IL(REF) = 1mA
– 2.4 4.2 µA
– 6.1 9.2 µA
Note 2. Pin5 input current must be limited to ±3mA. The addition of a 39kΩ resistor in series with
Pin5 allows ±100V signals without damage.
Note 4. Bar mode results when Pin9 is within 20mV of V+. Dot mode results when Pin9 is pulled at
least 200mV below V+ or left open circuit. LED No. 10 (Pin10 output current) is disabled if
Pin9 is pulled 0.9V or more below VLED.
Threshold Voltage: (Note 3)
Output dB
Min
Typ
1 –27 0.422
0.447
1 –24 0.596
0.631
3 –21 0.841
0.891
4 –18 1.189
1.259
5 –15 1.679
1.778
Max
0.531
0.750
1.059
1.413
1.995
Output dB
6 –12
7 –9
8 –6
9 –3
10
0
Min
2.372
3.350
4.732
6.683
9.985
Typ
2.512
3.548
5.012
7.079
10.000
Max
2.819
3.825
5.309
7.498
10.015
Note 3. Accuracy is measured referred to +10.000VDC at Pin5, with + 10.000VDC at Pin6, and
0.000VDC at Pin4. At lower full–scale voltages, buffer and comparator offset voltage may
add significant error. See table for threshold voltages.
Share Link: 