PSP-500 데이터 시트보기 (PDF) - Total Power International
부품명
상세내역
일치하는 목록
PSP-500 Datasheet PDF : 5 Pages
| |||
500W with PFC and Parallel Function
PSP-500-P series
Features :
Universal AC input / Full range
Built-in active PFC function, PF>0.95
Protections:Short circuit/Over load/Over voltage/Over temperature
Foced air cooling by built-in DC fan
Current sharing up to 2000W(3+1)
With power good and fail signal output
Built-in remote ON-OFF control
Built-in remote sense function
3 years warranty
SPECIFICATION
MODEL
PSP-500-5P PSP-500-12P PSP-500-13.5P PSP-500-15P PSP-500-24P PSP-500-27P PSP-500-48P
OUTPUT
INPUT
DC VOLTAGE
5V
12V
13.5V
RATED CURRENT
80A
41.5A
37A
CURRENT RANGE
0 ~ 80A
0 ~ 41.5A
0 ~ 37A
RATED POWER
400W
498W
499.5W
RIPPLE & NOISE (max.) Note.2 100mVp-p
150mVp-p
150mVp-p
VOLTAGE ADJ. RANGE
4.75 ~ 5.5V
10 ~ 13.2V
12 ~ 15V
VOLTAGE TOLERANCE Note.3 2.0%
1.0%
1.0%
LINE REGULATION
0.5%
0.3%
0.3%
LOAD REGULATION
2.0%
0.5%
0.5%
SETUP, RISE TIME
1500ms, 50ms at full load
HOLD TIME (Typ.)
24ms at full load
VOLTAGE RANGE Note.5 90 ~ 264VAC 127 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
0.95/230VAC 0.98/100VAC at full load
EFFICIENCY (Typ.)
76%
82%
82%
AC CURRENT (Typ.)
7A/115AVC 3.5A/230VAC
INRUSH CURRENT (Typ.) 20A/115VAC 40A/230VAC
15V
33A
0 ~ 33A
495W
150mVp-p
13.5 ~ 18V
1.0%
0.3%
0.5%
82%
24V
20.8A
0 ~ 20.8A
499.2W
150mVp-p
20 ~ 26.4V
1.0%
0.2%
0.5%
27V
18.5A
0 ~ 18.5A
499.5W
150mVp-p
24 ~ 30V
1.0%
0.2%
0.5%
84%
84%
48V
10.5A
0 ~ 10.5A
504W
200mVp-p
41 ~ 56V
1.0%
0.2%
0.5%
86%
LEAKAGE CURRENT
<1mA / 240VAC
OVER LOAD
110 ~ 125% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
FUNCTION REMOTE CONTROL
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V
27.6 ~ 32.4V
Protection type : Shut down o/p voltage, re-power on to recover
RTH2 95 Detect on heatsink of Q1,Q7 power transistor & L3 output choke
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off sink current <4 ~ 10mA
-10 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH with 30CFM forced air non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL1950, TUV EN60950-1 Approved
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
31 ~ 36.5V
57.6 ~ 67.2V
SAFETY &
EMC
(Note 4)
OTHERS
NOTE
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A
MTBF
130.1K hrs min. MIL-HDBK-217F (25 )
DIMENSION
250*123*50mm (L*W*H)
PACKING
1.3Kg; 6pcs/7.8Kg/0.89CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
Share Link: 