TC1188(2002) 데이터 시트보기 (PDF) - Microchip Technology

부품명

상세내역

일치하는 목록

TC1188
(Rev.:2002)

MAX8863/64 Pin Compatible, Low Dropout, 120 mA Linear Regulators

Microchip Technology 

TC1188/TC1189

1.0 ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings*

Input Voltage .........................................................6.5V

Output Short-Circuit Duration .............................Infinite

Output Voltage .......................... (-0.3V) to (VIN + 0.3V)

Maximum Voltage On Any Pin.... (-0.3V) to (VIN +0.3V)

Continuous Power Dissipation (TA = +70°C)

SOT-23-5 (derate 7.1 mW/°C above +70°C)

..................................................................571 mW

Operating Temperature Range............... -40°C to 85°C

Storage Temperature .........................-65°C to +160°C

Lead Temperature (Soldering, 10 Sec.) ........... +300°C

*Notice: *Stresses above those listed under "Absolute

Maximum Ratings" may cause permanent damage to

the device. These are stress ratings only and functional

operation of the device at these or any other conditions

above those indicated in the operation sections of the

specifications is not implied. Exposure to Absolute

Maximum Rating conditions for extended periods may

affect device reliability.

DC SPECIFICATIONS

Electrical Characteristics: VIN = +3.6V, GND = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.

(Note 1)

Parameters

Symbol

Min

Typ Max Units

Conditions

Input Voltage

VIN

VOUT+0.5V

—

6.0

V VOUT ≥ 2.5V

2.7

—

6.0

VOUT = 1.8V (Note 2)

Output Voltage

VOUT

3.05

3.15 3.25

V 0 mA ≤ IOUT ≤ 50 mA T

2.75

2.84 2.93

V 0 mA ≤ IOUT ≤ 50 mA S

2.70

2.80 2.88

V 0 mA ≤ IOUT ≤ 50 mA R

1.745

1.80 1.85

V 0 mA ≤ IOUT ≤ 50 mA Q

Maximum Output Current

IOUT

120

—

—

mA

Current Limit

ILIM

—

280

—

mA Note 3

Input Current

IIN

—

50

90

µA IOUT = 0

Dropout Voltage

—

1.1

—

mV IOUT = 1 mA

—

55

120

mV IOUT = 50 mA

—

110

240

mV IOUT = 100 mA (Note 4)

Line Regulation

∆VLNR

-0.10

0.001 0.10

%/V VIN = VOUT + 0.5V to 6.0V

—

—

—

%/V IOUT = 1 mA

Load Regulation

∆VLDR

—

0.01 0.040 %/mA IOUT = 0 mA to 50 mA

Output Voltage Noise

—

350

—

µVRMS 10 Hz to 1 MHz, COUT = 1 µF

—

220

—

µVRMS 10 Hz to 1 MHz COUT = 100 µF

Wake Up Time

(from Shutdown Mode)

tWK

—

10

—

µsec VIN = 3.6V

CIN = 1 µF, COUT = 1 µF

IL = 30 mA, (See Figure 3-1)

Setting Time

(from Shutdown Mode)

tS

—

140

—

µsec VIN = 3.6V

CIN = 1 µF, COUT = 1 µF

IL = 30 mA, (See Figure 3-1)

Note 1: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are ensured through cor-

relation using Statistical Quality Control (SQC) methods.

2: Validated by line regulation test.

3: Not tested. For design purposes, the current limit should be considered 150 mA minimum to 410 mA maximum.

4: The dropout voltage is defined as (VIN – VOUT) when VOUT is 100 mV below the value of VOUT for

VIN = VOUT +2V.

DS21364B-page 2

 2002 Microchip Technology Inc.

Share Link: