RT9244 데이터 시트보기 (PDF) - Richtek Technology
부품명
상세내역
일치하는 목록
RT9244 Datasheet PDF : 15 Pages
| |||
RT9244
Design Example
Given:
Apply for three phase converter
VIN = 12V
VCORE = 1.5V
ILOAD (MAX) = 60A
VDROOP = 120mV at full load
OCP trip point set at 33A for each channel (S/H)
RDS(ON) = 6mΩ of low side MOSFET at 27°C
L = 2μH
COUT = 9,000μF with 2mΩ ESR.
1. Compensation Setting
a. Modulator Gain, Pole and Zero :
From the following formula :
V IN
12V
Modulator Gain =
V RAMP
= 1.9V× 3
= 4.2 (12.46dB)
2
where VRAMP : ramp amplitude of sawtooth wave
1
LC Filter Pole = 2π x LC = 1.2kHz and
1
ESR Zero = 2π x ESR x COUT = 8.8kHz
b. EA Compensation Network :
Select R1 = 2.4kΩ, R2 = 24kΩ, C1 = 6.6nF,
C2 = 33pF and use the type 2 compensation
scheme shown in Figure 5.
R2 C1
R3 C3
COMP
C2
R1
> VDIF
-
+
DACOUT
FB
R3,C3 are used in type
3 compensation scheme
(left NC in type 2)
Figure 5.
From the following formulas :
FZ =
1
, FP =
1
2π x R2 x C1
Middle Band Gain = R 2
2π x R2 x ⎜⎛ C1× C 2 ⎟⎞
⎝C1 + C2 ⎠
R1
By calculation, the FZ = 1kHz, FP = 200kHz and
Middle Band Gain is 10 (i.e 20dB).
The asymptotic bode plot of EA compensation and
PWM loop gain is shown as Figure 6.
www.richtek.com
12
Asymptotic Bode Plot of PWM Loop Gain
100
80
60
Uncompensated EA Gain
40
20
0
Compensated EA Gain
-20
PWM Loop Gain
-40
Modulator Gain
-60
1100
110000
110K00 11000K00 10100000K0 1010M0000 1010000M000
Frequency (Hz)
Figure 6.
2. Droop & DAC Offset Setting
For each channel the load current is 60A / 3 = 20A
and the ripple current, ΔIL, is given as :
5μs
x
1.5V
2uH
x
⎛⎜⎝1−
1.5V
12V
⎞⎟⎠
=
3.28A
The
load
current,
IL,
at
S/H
is 20A
−
ΔIL
2
= 18.36A
.
Using the following formula to select the appropriate
IX (MAX) for the S/H of GM amplifier :
IX (MAX) = R DS(ON) × 18.36A
R SP
The suggested IX is in the order of 50 to 60μA, select
RSP = RSN = 2kΩ, then IX (MAX) will be 55μA.
VDROOP = 120mV = 55μA × 2 × 3 (phase no.) × RADJ,
therefore RADJ will be 360Ω.
The RDS(ON) of MOSFET varies with temperature rise.
When the low side MOSFET working at 70°C and
5000ppm/°C temperature coefficient of RDS(ON), the
RDS(ON) at 70°C is given as :
6mΩ × {1+ (70°C − 27°C) × 5000ppm/°C} = 7.3mΩ.
RADJ at 70°C is given as :
RADJ_27°C × (RDS(ON)_27°C / RDS(ON)_70°C) = 296Ω
3. Over-Current Protection Setting
OCP trip point is internally set at around 100μA of IX
for each channel. As above-selected RSP = RSN = 2kΩ,
the OCP trip point is found using :
IX
(OCP)
=
RDS(ON) ×IL
RSP
(TRIP)
=
6mΩ × 33A
2kΩ
= 100μA
4. Soft-Start Capacitor Selection
CSS = 0.1μF is the suitable value for most application.
DS9244-06 March 2007
Share Link: 