PI5C16862CA 데이터 시트보기 (PDF) - Pericom Semiconductor
부품명
상세내역
일치하는 목록
PI5C16862CA Datasheet PDF : 4 Pages
| |||
PI5C16862C
20-Bit, 2-Port Bus Switch
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677w889900i11t22h3344U5566n7788d9900e11r2233s44h5566o77o8899t0011P22r1122o33t44e5566c77t88i99o0011n22
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature............................................................ –65°C to +150°C
Ambient Temperature with Power Applied ........................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & VCC Only) ... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) . –0.5V to +7.0V
DC Input Voltage ................................................................... –0.5V to +7.0V
DC Output Current .............................................................................. 120mA
Power Dissipation ................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation
of the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±10%)
Parameters
Description
Test Conditions(1)
Min.
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
IIH
Input HIGH Current
VCC = Max., VIN = VCC
—
IIL
Input LOW Current
VCC = Max., VIN = GND
—
IOZH
High Impedance Output Current 0 ≤ IN, YN ≤ VCC
—
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18mA
—
IOS
Short Circuit Current(3)
A(B) = 0V, B (A) = VCC
100
VH
Input Hysteresis at Control Pins
—
RON
Switch ON Resistance(3)
VCC = Min., VIN = 0.0V, ION = 48mA
VCC = Min., VIN = 2.4V, ION = 15mA
—
—
Typ.(2)
—
—
—
—
—
—
—
150
5.5
9
Max.
—
0.8
±1
±1
±1
–1.8
—
—
8
16
Units
V
µA
V
mA
mV
Ω
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5)
Description
Test Conditions
Typical
Units
CIN
Input Capacitance
VIN = 0V
6
COFF
A/B Capacitance, Switch Off
VIN = 0V
6
pF
CON
A/B Capacitance, Switch On
VIN = 0V
10
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, TA= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages
on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8391C
09/15/04
Share Link: 