N08M1618L1A 데이터 시트보기 (PDF) - AMI Semiconductor
부품명
상세내역
일치하는 목록
N08M1618L1A Datasheet PDF : 11 Pages
| |||
AMI Semiconductor, Inc.
N08M1618L1A
Advance Information
Absolute Maximum Ratings1
Item
Symbol
Rating
Unit
Voltage on any pin relative to VSS
Voltage on VCC Supply Relative to VSS
Power Dissipation
Storage Temperature
Operating Temperature
Soldering Temperature and Time
VIN,OUT
–0.3 to VCC+0.3
V
VCC
–0.3 to 4.5
V
PD
500
mW
TSTG
–40 to 125
oC
TA
-40 to +85
oC
TSOLDER
240oC, 10sec(Lead only)
oC
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min.
Typ1
Max Unit
Core Supply Voltage
I/O Supply Voltage
Data Retention Voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Read/Write Operating Supply Current
@ 1 µs Cycle Time2
Read/Write Operating Supply Current
@ 85 ns Cycle Time2
Page Mode Operating Supply Current
@ 85 ns Cycle Time2 (Refer to Power
Savings with Page Mode Operation
diagram)
VCC
VCCQ
VDR
VIH
VIL
VOH
VOL
ILI
ILO
ICC1
ICC2
ICC3
Read/Write Quiescent Operating Sup-
ply Current3
ICC4
Standby Current3
ISB1
Data Retention Current3
IDR
1.4
VCCQ > or = VCC
2.3
Chip Disabled3
1.2
VCCQ-0.6
–0.3
IOH = 0.2mA
VCCQ–0.2
IOL = -0.2mA
VIN = 0 to VCC
OE = VIH or Chip Disabled
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
1.8
1.5
10.0
2.2
V
3.6
V
V
VCCQ+0.3 V
0.6
V
V
0.2
V
0.1
µA
0.1
µA
2.5 mA
13.0 mA
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
3.5
mA
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0,
f=0
VIN = VCC or 0V
Chip Disabled
tA= 85oC, VCC = 2.2 V
VCC = 1.2V, VIN = VCC or 0
Chip Disabled, tA= 85oC
1
µA
0.5
20.0 µA
0.1
1.0
µA
1. Typical values are measured at Vcc=Vcc Typ., TA=25°C and not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
3. This device assumes a standby mode if the chip is disabled (CE1 high or CE2 low). In order to achieve low standby current all
inputs must be within 0.2 volts of either VCC or VSS.
Stock No. 23211-03 9/21/06
ADVANCE INFORMATION
3
The specifications of this device are subject to change without notice. For latest documentation see http://www.amis.com.
Share Link: 