MAX6409BS41-T 데이터 시트보기 (PDF) - Maxim Integrated
부품명
상세내역
일치하는 목록
MAX6409BS41-T Datasheet PDF : 8 Pages
| |||
Voltage Detectors in 4-Bump (2 X 2)
Chip-Scale Package
ABSOLUTE MAXIMUM RATINGS
All voltages measured to GND unless otherwise noted.
VCC ..........................................................................-0.3V to +6V
OUT/OUT ...................................................-0.3V to (VCC + 0.3V)
OUT (open-drain) .....................................................-0.3V to +6V
MR ..............................................................-0.3V to (VCC + 0.3V)
Input/Output Current into Any Pin .......................................20mA
Continuous Power Dissipation (TA = +70°C)
4-Pin/Bump UCSP (derate 3.8mW/°C above +70°C)....303mW
Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range ............................-65°C to +160°C
Bump Reflow Temperature .............................................+235°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 1.0V to 5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = 3V and TA = +25°C.) (Note1)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Supply Voltage Range
VCC
TA = 0°C to +70°C
TA = -40°C to +85°C
1.0
5.5
V
1.2
5.5
Supply Current
MAX6406/MAX6407/MAX6408
ICC
VCC = 3.0V for VTH ≤ 2.93V,
VCC = 3.2V for VTH > 2.93V, no load
0.5
1.0
µA
Detector Threshold
Voltage Threshold Hysteresis
Detector Threshold Tempco
MR Input
MR Minimum Input Pulse Width
MR Glitch Rejection
MR to OUT/OUT Delay
MR Pullup Resistance
Propagation Delay
Startup Time
VTH
∆VTH/°C
VIL
VIH
VIL
VIH
tMD
VCC = 5.5V, no load
Table 1
TA = +25°C
TA = -40°C to +85°C
MAX6406/MAX6407/MAX6408
MAX6409/MAX6410/MAX6411
VTH > 4.0V
VTH ≤ 4.0V
VCC = (VTH + 100mV) to (VTH - 100mV)
VCC = (VTH - 100mV) to (VTH + 100mV)
VCC = 0 to VTH (min)
1.0 1.75
VTH - 1.5% VTH VTH + 1.5%
VTH - 2.5% VTH VTH + 2.5%
6.3
9.5
40
0.8
2.0
0.2 x VCC
0.7 x VCC
1
100
200
25
50
75
20
42
88
V
mV
ppm/°C
V
µs
ns
ns
kΩ
µs
µs
OUT Output Voltage Low
(MAX6406/MAX6408/MAX6409/
MAX6411)
ISINK = 1.6mA, VCC ≥ 2.1V, OUT asserted
VOL
ISINK = 100µA, VCC ≥ 1.2V, OUT asserted
0.3
V
0.4
ISOURCE = 500µA, VCC = 3.2V, MAX6406,
OUT not asserted
0.8 x VCC
OUT Output Voltage High
(MAX6406/MAX6409)
VOH
ISOURCE = 800µA, VCC = 4.5V,
VTH ≤ 4.38V, OUT not asserted
0.8 x VCC
V
ISOURCE = 800µA, VCC = VTH (max),
VTH ≥ 4.5V, OUT not asserted
0.8 x VCC
2 _______________________________________________________________________________________
Share Link: 