UWR-1.5/6000-D12A 데이터 시트보기 (PDF) - DATEL Data Acquisition products
부품명
상세내역
일치하는 목록
UWR-1.5/6000-D12A Datasheet PDF : 8 Pages
| |||
9-15W, SINGLE OUTPUT DC/DC CONVERTERS
UWR Models
Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage and full-load conditions, unless noted. ➀ ➁
Input
Input Voltage Range:
D12A Models
D24A Models
D48A Models
10-18 Volts (12V nominal)
18-36 Volts (24V nominal)
36-75 Volts (48V nominal)
Overvoltage Shutdown:
D12A Models
D24A Models
D48A Models
18.5-21 Volts (20V typical)
37-40 Volts (38V typical)
77-81 Volts (78.5V typical)
Start-Up Threshold: ➂
D12A Models
D24A Models
D48A Models
9.4-9.8 Volts (9.6V typical)
16.5-18 Volts (17V typical)
34-36 Volts (35V typical)
Undervoltage Shutdown: ➂
D12A Models
D24A Models
D48A Models
7.5-8.5 Volts (8V typical)
16-17 Volts (16.5V typical)
32.5-35.5 Volts (34V typical)
Input Current:
Normal Operating Conditions
Standby Mode (Off, OV, UV)
See Ordering Guide
5mA
Input Filter Type
Pi
Reverse-Polarity Protection
Brief duration, 10A maximum
On/Off Control (Optional, Pin 3): ➃ ➄
D12AC, D24AC, & D48AC Models
D12AN, D24AN, & D48AN Models
On = open or 13V - +VIN, IIN = 50µA max.
Off = 0-0.8V, IIN = 1mA max.
On = 0-0.8V, IIN = 2.6mA max.
Off = open or 3.3-5.5V, IIN = 1mA max.
Sync (Optional, Pin 3) ➂ ➃
Input Threshold (Rising edge active)
Input Voltage Low
Input Voltage High
Input Resistance
Output High Voltage (100µA load)
Output Drive Current
Input/Output Pulse Width
1-2.7 Volts
0-0.9 Volts
2.8-5 Volts
35kΩ minimum
3.5-4.8 Volts
35mA
160-360nsec
Output
VOUT Accuracy (50% load):
1.5V/1.8V/2.5V/3.3V Outputs
5/12/15V Outputs
±1.5%, maximum
±1%, maximum
Minimum Loading for Specification: ➁
1.5V/1.8V/2.5V/3.3V/5V Outputs
No load
12V/15V Outputs
10% of IOUT max.
Minimum Loading for Stability: ➁
1.5V/1.8V/2.5V/3.3V/5V Outputs
12V/15V Outputs
No load
25mA
Ripple/Noise (20MHz BW) ➀ ➅
See Ordering Guide
Line/Load Regulation
See Ordering Guide
Efficiency
See Ordering Guide
Isolation Voltage:
Input-to-Output
1500Vdc minimum
Isolation Capacitance
470pF
Isolation Resistance
100MΩ
Current Limiting:
1.5V/1.8V/2.5V/3.3V/5V Outputs
12V/15V Outputs
Hiccup technique, auto-recovery
Power-limiting technique, auto-recovery
Overvoltage Protection
Zener/transorb clamp, magnetic feedback
Temperature Coefficient
±0.04% per °C.
Dynamic Characteristics
Transient Response (50% load step) 200µsec max. to ±1.5% of final value
Start-Up Time: ➂
VIN to VOUT
On/Off to VOUT
50msec
30msec
Switching Frequency
310kHz (±30kHz)
Environmental
Operating Temperature (Ambient):
Without Derating ➆
With Derating
–40 to +60/70°C
to +100°C (See Derating Curves)
Case Temperature:
Maximum Allowable
+100°C
Storage Temperature
–40 to +105°C
Physical
Dimensions
2" x 1" x 0.49" (51 x 25 x 12.45mm)
Shielding
None
Case Material
Diallyl phthalate, UL94V-0 rated
Pin Material
Brass, solder coated
Weight
1.4 ounces (39.7 grams)
➀ All models are specified with two external 0.47µF multi-layer ceramic capacitors installed
across their output pins.
➁ See Minimum Output Loading Requirements under Technical Notes.
➂ See Technical Notes for details.
➃ The On/Off Control, Sync and Trim functions are optional and must be installed by DATEL.
See Optional Functions or contact DATEL for details.
➄ The On/Off Control is designed to be driven with open-collector logic or the application of
appropriate voltages (referenced to –Input (Pin 2)). Applying a voltage to the On/Off Control
pin when no input voltage is applied to the converter may cause permanent damage.
See Technical Notes.
➅ Output noise maybe further reduced with the addition of additional external output
capacitors. See Technical Notes.
➆ Operating temperature range without derating is model and input-voltage dependent.
See Temperature Derating.
Absolute Maximum Ratings
Input Voltage:
Continuous:
D12 Models
D24 Models
D48 Models
Transient (100msec):
D12 Models
D24 Models
D48 Models
Input Reverse-Polarity Protection
Output Overvoltage Protection:
1.5/1.8V Outputs
2.5V/3.3V Outputs
5V/12V/15V Outputs
Output Current
Case Temperature
Storage Temperature
Lead Temperature (soldering, 10 sec.)
22 Volts
44 Volts
88 Volts
50 Volts
50 Volts
100 Volts
Current must be <10 Amps. Brief
duration only. Fusing recommended.
TBD/TBD Volts, unlimited duration
TBD/4.5 Volts, unlimited duration
6.8/15/18 Volts, unlimited duration
Current limited. Devices can
withstand sustained output short
circuits without damage.
+100°C
–40 to +105°C
+300°C
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied.
3
Share Link: 