HIP6311(2000) 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
일치하는 목록
HIP6311 Datasheet PDF : 17 Pages
| |||
HIP6311
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V
Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5KV
Recommended Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief 379 for details.
Electrical Specifications Operating Conditions: VCC = 5V, TA = 0oC to 70oC, Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
MIN
INPUT SUPPLY POWER
Input Supply Current
RT = 100kΩ, Active and Disabled Maximum Limit
-
POR (Power-On Reset) Threshold
VCC Rising
4.25
VCC Falling
3.75
REFERENCE AND DAC
System Accuracy
Percent system deviation from programmed VID Codes
-0.8
DAC (VID0 - VID4) Input Low Voltage
DAC Programming Input Low Threshold Voltage
-
DAC (VID0 - VID4) Input High Voltage
DAC Programming Input High Threshold Voltage
2.0
VID Pull-Up
VIDx = 0V or VIDx = 3V
10
CHANNEL GENERATOR
Frequency, FSW
RT = 100kΩ, ±1%
245
Adjustment Range
See Figure 10
0.05
Disable Voltage
ERROR AMPLIFIER
Maximum voltage at FS/DIS to disable controller. IFS/DIS = 1mA.
-
DC Gain
RL = 10K to ground
-
Gain-Bandwidth Product
CL = 100pF, RL = 10K to ground
-
Slew Rate
CL = 100pF, Load = ±400µA
-
Maximum Output Voltage
Load = 400µA
3.6
Minimum Output Voltage
Load = -400µA
-
ISEN
Full Scale Input Current
-
Over-Current Trip Level
-
POWER GOOD MONITOR
Under-Voltage Threshold
VSEN Rising
-
Under-Voltage Threshold
VSEN Falling
-
PGOOD Low Output Voltage
IPGOOD = 4mA
-
PROTECTION
Over-Voltage Threshold
VSEN Rising
1.12
Percent Over-Voltage Hysteresis
VSEN Falling after Over-Voltage
-
TYP
10
4.38
3.88
-
-
-
20
275
-
-
72
18
5.3
4.1
0.16
50
82.5
0.92
0.90
0.18
1.15
2
MAX UNITS
15 mA
4.5
V
4.00 V
0.8 %
0.8
V
-
V
40 µA
305 kHz
1.5 MHz
1.0
V
-
dB
- MHz
- V/µs
-
V
0.5
V
-
µA
-
µA
- VDAC
- VDAC
0.4
V
1.2 VDAC
-
%
6
Share Link: 