CS51411(2002) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
일치하는 목록
CS51411
(Rev.:2002)
(Rev.:2002)
ON Semiconductor
CS51411 Datasheet PDF : 16 Pages
| |||
CS51411, CS51412, CS51413, CS51414
ID(AVG)
+
IO(VIN *
VIN
VO)
The worse case of the diode average current occurs during
maximum load current and maximum input voltage. For the
diode to survive the short circuit condition, the current rating
of the diode should be equal to the Foldback Current Limit.
See Table 1 for schottky diodes from ON Semiconductor
which are suggested for CS5141X regulator.
Inductor Selection
When choosing inductors, one might have to consider
maximum load current, core and copper losses, component
height, output ripple, EMI, saturation and cost. Lower
inductor values are chosen to reduce the physical size of the
inductor. Higher value cuts down the ripple current, core
losses and allows more output current. For most
applications, the inductor value falls in the range between
2.2 µH and 22 µH. The saturation current ratings of the
inductor shall not exceed the IL(PK), calculated according to
IL(PK)
+
IO
)
VO(VIN * VO)
2(fS)(L)(VIN)
The DC current through the inductor is equal to the load
current. The worse case occurs during maximum load
current. Check the vendor’s spec to adjust the inductor value
under current loading. Inductors can lose over 50% of
inductance when it nears saturation.
The core materials have a significant effect on inductor
performance. The ferrite core has benefits of small physical
size, and very low power dissipation. But be careful not to
operate these inductors too far beyond their maximum
ratings for peak current, as this will saturate the core.
Powered Iron cores are low cost and have a more gradual
saturation curve. The cores with an open magnetic path, such
as rod or barrel, tend to generate high magnetic field
radiation. However, they are usually cheap and small. The
cores providing a close magnetic loop, such as pot–core and
toroid, generate low electro–magnetic interference (EMI).
There are many magnetic component vendors providing
standard product lines suitable for CS5141X. Table 2 lists
three vendors, their products and contact information.
Part Number
1N5817
1N5818
1N5819
MBR0520
MBR0530
MBR0540
MBRS120
MBRS130
MBRS140
VBREAKDOWN (V)
20
30
40
20
30
40
20
30
40
Table 1.
IAVERAGE (A)
1.0
1.0
1.0
0.5
0.5
0.5
1.0
1.0
1.0
V(F) (V) @ IAVERAGE
0.45
0.55
0.6
0.385
0.43
0.53
0.55
0.395
0.6
Package
Axial Lead
Axial Lead
Axial Lead
SOD–123
SOD–123
SOD–123
SMB
SMB
SMB
Vendor
Coiltronics
Coilcraft
Pulse
Table 2.
Product Family
UNI–Pac1/2: SMT, barrel
THIN–PAC: SMT, toroid, low profile
CTX: Leaded, toroid
DO1608: SMT, barrel
DS/DT 1608: SMT, barrel, magnetically shielded
DO3316: SMT, barrel
DS/DT 3316: SMT, barrel, magnetically shielded
DO3308: SMT, barrel, low profile
–
Web Site
www.coiltronics.com
www.coilcraft.com
www.pulseeng.com
Telephone
(516) 241–7876
(800) 322–2645
(619) 674–8100
http://onsemi.com
12
Share Link: