ATF1508ASZ-25QI100(1998) 데이터 시트보기 (PDF) - Atmel Corporation

부품명

상세내역

일치하는 목록

ATF1508ASZ-25QI100
(Rev.:1998)

High Performance E2 PLD

Atmel Corporation 

ATF1508AS/Z

All ATF1508s also have an optional power down mode. In

this mode, current drops to below 10 mA. When the power

down option is selected, either PD1 or PD2 pins (or both)

can be used to power down the part. The power down

option is selected in the design source file. When enabled,

the device goes into power down when either PD1 or PD2

is high. In the power down mode, all internal logic signals

are latched and held, as are any enabled outputs.

All pin transitions are ignored until the PD pin is brought

low. When the power down feature is enabled, the PD1 or

PD2 pin cannot be used as a logic input or output. How-

ever, the pin’s macrocell may still be used to generate bur-

ied foldback and cascade logic signals.

All Power-Down AC Characteristic parameters are com-

puted from external input or I/O pins, with Reduced Power

Bit turned on. For macrocells in reduced-power mode

(Reduced power bit turned on), the reduced power adder,

tRPA, must be added to the AC parameters, which include

the data paths tLAD, tLAC, tIC, tACL, tACH and tSEXP.

Each output also has individual slew rate control. This may

be used to reduce system noise by slowing down outputs

that do not need to operate at maximum speed. Outputs

default to slow switching, and may be specified as fast

switching in the design file.

Design Software Support

ATF1508AS designs are supported by several third party

tools. Automated fitters allow logic synthesis using a variety

of high level description languages and formats.

Power Up Reset

The ATF1508AS has a power-up reset option at two differ-

ent voltage trip levels when the device is being powered

down. Within the fitter, or during a conversion, if the

“power-reset” option is turned “on” ( which is the default

option), the trip levels during power up or power down is at

2.8V. The user can change this default option from “on” to

“off” (within the fitter or specify it as a switch during conver-

sion). When this is done, the voltage trip level during

power-down changes from 2.8V to 0.7V. This is to ensure a

robust operating environment.

The registers in the ATF1508AS are designed to reset dur-

ing power up. At a point delayed slightly from VCC crossing

VRST, all registers will be reset to the low state. The output

state will depend on the polarity of the buffer.

This feature is critical for state machine initialization. How-

ever, due to the asynchronous nature of reset and the

uncertainty of how VCC actually rises in the system, the fol-

lowing conditions are required:

1. The VCC rise must be monotonic,

2. After reset occurs, all input and feedback setup times

must be met before driving the clock pin high, and,

3. The clock must remain stable during TPR.

Security Fuse Usage

A single fuse is provided to prevent unauthorized copying

of the ATF1508AS fuse patterns. Once programmed, fuse

verify is inhibited. However, User Signature and device ID

remains accessible.

Programming

ATF1508AS devices are In-System Programmable (ISP)

devices utilizing the 4-pin JTAG protocol. This capability

eliminates package handling normally required for program

and facilitates rapid design iterations and field changes.

Atmel provides ISP hardware and software to allow pro-

gramming of the ATF1508AS via the PC. ISP is perfomed

by using either a download cable, or a comparable board

tester or a simple microprocessor interface.

To facilitate ISP programming by the Automated Test

Equipment (ATE) vendors, Serial Vector Format (SVF)

files can be created by Atmel provided Software utilities.

ATF1508AS devices can also be programmed using stan-

dard 3rd party programmers. With 3rd party programmer

the JTAG ISP port can be disabled thereby allowing 4 addi-

tional I/O pins to be used for logic.

Contact your local Atmel representatives or Atmel PLD

applications for details.

ISP Programming Protection

The ATF1508AS has a special feature which locks the

device and prevents the inputs and I/O from driving if the

programming process is interrupted due to any reason. The

inputs and I/O default to high-Z state during such a condi-

tion. In addition the pin keeper option preserves the former

state during device programming.

All ATF1508AS devices are initially shipped in the erased

state thereby making them ready to use for ISP.

Note:

For more information refer to the “Desigining for In-Sys-

tem Programmability with Atmel CPLDs” application

note.

7

Share Link: