5962R9582401QQC(1996) 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
일치하는 목록
5962R9582401QQC Datasheet PDF : 19 Pages
| |||
HS-80C85RH
HS-80C85RH Caveats
1. An important caveat that is applicable to CMOS devices in gen-
eral is that unused inputs should never be left floating. This rule
also applies to inputs connected to a tri- state bus. The need for
external pull-up resistors during tri-state bus conditions is elimi-
nated by the presence of regenerative latches on the following
HS-80C85RH output pins: AD0-AD7, A8-A15, and IO/M. Figure
10 depicts an output and corresponding regenerative latch.
When the output driver assumes the high impedance state, the
latch holds the bus in whatever logic state (high or low) it was be-
fore the tri-state condition. A transient drive current of approxi-
mately ±1.0mA at 0.5 VDD for 10nsec is required to switch the
latch. Thus, CMOS device inputs connected to the bus are not
allowed to float during tri-state conditions.
2. The RD and WR pins of the HS-80C85RH contain internal dy-
namic pull-up transistors to avoid spurious selection of memory
devices when the RD and WR pins assume the high impedance
state. This eliminates the need for external resistive pull-ups on
these pins.
3. The RESET IN and X1 inputs on the HS-80C85RH are schmit
trigger inputs. This eliminates the possibility of internal oscilla-
tions in response to slow rise time input signals at these pins.
4. A high frequency bypass capacitor of approximately 0.1 µF
should be connected between VDD and GND to shunt power
supply transients.
5. The HS-80C85RH is functional within 10 input clock cycles after
application of power (assuming that reset has been asserted
from power-on). Start up conditions in the crystal controlled
oscillator mode must also account for the characteristics of the
oscillator.
System Interface
The HS-80C85RH family includes memory components,
which are directly compatible to the HS-8OC8SRH CPU. For
example, a system consisting of the three radiation-
hardened chips, HS-80C85RH, HS-81C56RH, and
HS-83C55RH will have the following features:
1. 2K Bytes ROM
2. 256 Bytes RAM
3. 1 Timer/Counter
4. 4 8-bit I/O Ports
5. 1 6-bit I/O Port
6. 4 Interrupt Levels
7. Serial In/Serial Out Ports
This minimum system, using the standard I/O technique is
as shown in Figure 12.
In addition to standard 1/0, the memory mapped I/O offers
an efficient I/O addressing technique. With this technique, an
area of memory address space is assigned for I/O address,
thereby, using the memory address for I/O manipulation.
Figure 13 shows the system configuration of Memory
Mapped I/O using HS-80C85RH.
The HS-80C85RH CPU can also interface with the standard
radiation-hardened memory that does not have the
multiplexed address/data bus. It will require use of the
HS-82C12RH (8-bit latch) as shown in Figure 14.
OUTPUT
DRIVER
REGENERATIVE
LATCH
OUTPUT
PIN
FIGURE 10. OUTPUT DRIVER AND LATCH FOR PINS ADO-AD7,
A8-A15 AND IO/M.
Generating An HS-80C85RH Wait State
If your system requirements are such that slow memories or
peripheral devices are being used, the circuit shown in
Figure 11 may be used to insert one WAIT state in each
HS-80C85RH machine cycle.
The D flip-flops should be chosen so that:
1. CLK is rising edge-triggered
2. CLEAR is low-level active.
The READY line is used to extend the read and write pulse
lengths so that the 80C85RH can be used with slow mem-
ory. HOLD causes the CPU to relinquish the bus when it is
through with it by floating the Address and Data Buses.
ALE †
VDD
CLEAR
CLK
“D”
F/F
D
80C85RH
CLK
OUTPUT
Q
CLK
“D”
F/F
D
TO
80C85RH
READY
INPUT
Q
†ALE and CLK (OUT) should be buffered if CLK
input of latch exceeds 80C85RH IOL or IOH.
FIGURE 11. GENERATION OF A WAIT STATE FOR HS-80C85RH
CPU.
VSS VDD
TRAP X1
X2
RESET INHOLD
RST 7.5
HLDA
RST 6.5
RST 5.5
HS-80C85RH
SOD
SID
INTR
S1
INTA ADDR/
RESET
S0
ADDR DATA ALE RD WR IO/M OUTRDY CLK
VSS VDD
(8) (8)
CE PORT
WR
A
(8)
RD PORT
(8)
ALE
B
DATA/ PORT
(6)
ADDR
C
IO/M
IN
TIMER
RESET OUT
IOW
RD
ALE
CE
A0-10
PORT
A
DATA/
ADDR
IO/M PORT
RESET
B
RDY †
CLK
IOR
(8)
(8)
VDD
VSS VDD
VDD
† Optional Connection
FIGURE 12. HS-80C85RH MINIMUM SYSTEM (STANDARD I/O
TECHNIQUE)
Spec Number 518054
14
Share Link: 