10XS3435 데이터 시트보기 (PDF) - Freescale Semiconductor

부품명

상세내역

일치하는 목록

10XS3435

Quad High Side Switch (Dual 10 mOhm, Dual 35 mOhm)

Freescale Semiconductor 

ELECTRICAL CHARACTERISTICS

STATIC ELECTRICAL CHARACTERISTICS

Table 4. Static Electrical Characteristics (continued)

Characteristics noted under conditions 6.0 V ≤ VPWR ≤ 20 V, 3.0 V ≤ VDD ≤ 5.5 V, -40°C ≤ TA ≤ 125°C, GND = 0 V unless

otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless

otherwise noted.

Characteristic

Symbol

Min

Typ

Max

Unit

OUTPUTS HS0 TO HS3 (CONTINUED)

HS[0,1] Current Sense Ratio (CSR0) Accuracy (6.0 V < VHS < 20 V)

with 28 W bit=1

Output Current

3.0 A

1.5 A

CSR0_1_ACC

%

-16

–

16

-20

–

20

HS[0,1] Current Recopy Accuracy with one calibration point (6.0 V < VHS[0:3] <

20 V)(17)

CSR0_0_ACC(

CAL)

-5.0

–

5.0

%

Output Current

5.0 A

HS[0,1] CSR0 Current Recopy Temperature Drift (6.0 V < VHS[0:3] < 20 V)

with 28 W bit=0(18)

Output Current

5.0 A

Δ(CSR0_0)/

Δ(T)

%/°C

0.04

HS[0,1] Current Sense Ratio (CSR1) Accuracy (6.0 V < VHS[0:3] < 20 V)

CSR1_0_ACC

%

with 28 W bit=0

Output Current

12.5 A

75 A

-17

–

+17

-12

–

+12

Current Sense Clamp Voltage

CSNS Open; IHS[0:3] = 5.0 A with CSR0 ratio

OFF Open-Load Detection Source Current(19)

OFF Open-Load Fault Detection Voltage Threshold

ON Open-Load Fault Detection Current Threshold

ON Open-Load Fault Detection Current Threshold with LED

VHS[0:3] = VPWR - 0.75 V

Output Short to VPWR Detection Voltage Threshold

Output programmed OFF

VCL(CSNS)

V

VDD+0.2

–

5

VDD+1.0

IOLD(OFF)

30

–

100

μA

VOLD(THRES)

2.0

3.0

4.0

V

IOLD(ON)

100

300

600

mA

IOLD(ON_LED)

mA

2.5

5.0

10

VOSD(THRES)

V

VPWR- VPWR-0.8 VPWR-0.4

1.2

Output Negative Clamp Voltage

0.5 A < IHS[0:3] < 5.0 A, Output programmed OFF

VCL

V

- 22

–

-16

Output Over-temperature Shutdown for 4.5 V < VPWR < 28 V

TSD

155

175

195

°C

Notes

17. Based on statistical analysis. It is not production tested.

18. Based on statistical data: delta(CSR0)/delta(T)={(measured ICSNS at T1 - measured ICSNS at T2) / measured ICSNS at room} / {T1-T2}.

No production tested.

19. Output OFF Open-Load Detection Current is the current required to flow through the load for the purpose of detecting the existence

of an open-load condition when the specific output is commanded OFF. Pull-up current is measured for VHS=VOLD(THRES)

Analog Integrated Circuit Device Data

Freescale Semiconductor

10XS3435

11

Share Link: