PI5X1018 데이터 시트보기 (PDF) - Pericom Semiconductor
부품명
상세내역
일치하는 목록
PI5X1018 Datasheet PDF : 7 Pages
| |||
PI5X1018
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223314485566-77B8899i00t11,2213344055-66P7788o99r0011t22C3344r5566o77s8899s00b1122a11r2233S4455w6677i88t99c00h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ........................................................ –65°C to +150°C
Ambient Temperature with Power Applied ....................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ..... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) . –0.5V to +7.0V
DC Input Voltage ................................................................ –0.5V to +7.0V
DC Output Current ........................................................................... 120mA
Power Dissipation ............................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other conditions
above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 4.5V to 5.5V)
Parameters
Description
Test Conditions(1)
Min. Typ.(2)
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
-0.5
IIH
Input HIGH Current
VCC = Max., VIN = VCC, VBIAS = OPEN
IIL
Input LOW Current
VCC = Max., VIN = GND, VBIAS = OPEN
IOZH
High Impedence
Output Current
0 ≤ N, M ≤ VCC, VBIAS = OPEN
IOZL
Low Impedence
Output Current
VIN = 0V, VBIAS = OPEN
VIK
Clamp Diode Voltage VCC = Min., IIN = −18mA
IOS
Short Circuit Current(3) N(M) = 0V, M(N) = VCC
100
VH
Input Hysteresis at
Control Pins
150
Bits 0-9
VCC = Min., VIN = 0.0V, ION = 48mA
All other bits
RON
Switch On Resistance(4)
Bits 0-9
VCC = Min., VIN = 2.4V, ION = 15mA
All other bits
Max.
0.8
±400
±400
±1
±400
-1.8
20
25
30
40
Units
V
µΑ
V
mA
mV
Ω
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5) Description
Test Conditions Typ. Units
CIN
COFF
Control Input Capacitance
Port Pin Capacitance, Port Disconnected
VIN = 0V
VIN = 0V
4
pF
27
pF
CON
Port Pin Capacitance, Port Connected to One Other Port
VIN = 0V
52
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between N and M pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (N,M) pins.
5. This parameter is guaranteed by design.
6. Where N is a pin of any port and M is a pin of any other port.
4
PS8365E 08/24/99
Share Link: 