MC100E211 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
일치하는 목록
MC100E211 Datasheet PDF : 12 Pages
| |||
MC10E211, MC100E211
MAXIMUM RATINGS (Note 1.)
Symbol
Parameter
Condition 1
Condition 2
Rating
Units
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI VCC
VI VEE
8
V
–8
V
6
V
–6
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
θJA
Thermal Resistance (Junction to Ambient) 0 LFPM
500 LFPM
28 PLCC
28 PLCC
± 0.5
0 to +85
–65 to +150
63.5
43.5
mA
°C
°C
°C/W
°C/W
θJC
Thermal Resistance (Junction to Case)
std bd
VEE
PECL Operating Range
NECL Operating Range
28 PLCC
22 to 26
4.2 to 5.7
–5.7 to –4.2
°C/W
V
V
Tsol
Wave Solder
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
265
°C
10E SERIES PECL DC CHARACTERISTICS VCCx= 5.0 V; VEE= 0.0 V (Note 1.)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2.)
Output LOW Voltage (Note 2.)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
119 160
119 160
119 160 mA
3980 4070 4160 4020 4105 4190 4090 4185 4280 mV
3050 3210 3370 3050 3210 3370 3050 3227 3405 mV
3830 3995 4160 3870 4030 4190 3940 4110 4280 mV
3050 3285 3520 3050 3285 3520 3050 3302 3555 mV
3.62
3.63 3.65
3.75 3.69
3.81 V
2.4
4.6 2.4
4.6 2.4
4.6
V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 µA
0.5 0.3
0.5 0.25
0.3 0.2
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / –0.06 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
10E SERIES NECL DC CHARACTERISTICS VCCx= 0.0 V; VEE= –5.0 V (Note 1.)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2.)
Output LOW Voltage (Note 2.)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
119 160
119 160
119 160 mA
–1020 –930 –840 –980 –895 –810 –910 –815 –720 mV
–1950 –1790 –1630 –1950 –1790 –1630 –1950 –1773 –1595 mV
–1170 –1005 –840 –1130 –970 –810 –1060 –890 –720 mV
–1950 –1715 –1480 –1950 –1715 –1480 –1950 –1698 –1445 mV
–1.38
–1.37 –1.35
–1.25 –1.31
–1.19 V
–2.6
–0.4 –2.6
–0.4 –2.6
–0.4 V
IIH
Input HIGH Current
150
150
150 µA
IIL
Input LOW Current
0.5 0.3
0.5 0.065
0.3 0.2
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / –0.06 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
http://onsemi.com
3
Share Link: 