MT8976 데이터 시트보기 (PDF) - Mitel Networks

부품명

상세내역

일치하는 목록

MT8976

ISO-CMOS ST-BUS™ FAMILY T1/ESF Framer Circuit

Mitel Networks 

ISO-CMOS MT8976

Pin Description (Continued)

Pin #

DIP PLCC

Name

Description

12 19

CSTi0

Control ST-BUS Input #0. A 2048 kbit/s serial control stream that contains 24 per

channel control words and two master control words.

13 20

E8Ko

Extracted 8 kHz Output. The E1.5i clock is internally divided by 193 to produce an 8

kHz clock which is aligned with the received DS1 frame and output at this pin. The8

kHz signal is derived from C1.5 in Digital Loopback mode.

14 6,

18,

22

VSS

System Ground.

15 23

XCtl External Control (Output). This is an uncommitted external output pin which is set

or reset via bit 3 in Master Control Word 1 on CSTi0. The state of XCtl is updated

once per frame.

16 24

XSt

External Status (Schmitt Trigger Input). The state of this pin is sampled once per

frame and the status is reported in bit 5 of Master Status Word 2 on CSTo.

17 26

CSTo

Control ST-BUS Output. This is a 2048 kbit/s serial control stream which provides

the 24 per-channel status words, and two master status words.

18 27 RxFDLClk Receive Facility Data Link Clock (Output). A 4 kHz clock signal used to clock out

FDL information. The data is clocked out on the rising edge of RxFDLClk.

19 28

DSTi

Data ST-BUS Input. This pin accepts a 2048 kbit/s serial stream which contains the

24 PCM or data channels to be transmitted on the T1 trunk.

20 29

RxFDL

Received Facility Data Link (Output). A 4 kHz serial output stream that is

demultiplexed from the FDL in ESF mode, or the received FS bit pattern in SLC-96

mode. It is clocked out on the rising edge of RxFDLClk.

21 34

C2i

2.048 MHz Clock Input. This is the master clock used for clocking serial data into

DSTi, CSTi0 and CSTi1. It is also used to clock serial data out of CSTo and DSTo.

22 37

TxSF

Transmit Superframe Pulse Input. A low going pulse applied at this pin will make

the next transmit frame the first frame of a superframe. The device will free run if this

pin is held high.

23 38

RxSF

Received Superframe Pulse Output. A pulse output on this pin designates that the

next frame of data on the ST-BUS is from frame 1 of the received superframe. The

period is 12 frames long in D3/D4 modes and 24 frames in ESF mode. Pulses are

output only when the device is synchronized to the received DS1 signal.

24 39

C1.5i

1.544 MHz Clock Input. This is the DS1 transmit clock and is used to output data on

TxA and TxB. It must be phase-locked to C2i. Data is clocked out on the rising

edge of C1.5i.

25 40

E1.5i

1.544 MHz Extracted Clock (Input). This clock which is extracted from the received

data is used to clock in data at RxA, RxB and RxD . The falling edge of the is

nominally aligned with the center of the received bit on RxD, RxA and RxB.

26 42

F0i

Frame Pulse Input. This is the frame synchronization signal which defines the

beginning of the 32 channel ST-BUS frame.

27 44

28 1

IC

Internal Connection. Tied to VSS for normal operation.

VDD

Positive Power Supply Input. +5V ± 5%.

4-31

Share Link: