HI1-0546-2(1999) 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
일치하는 목록
HI1-0546-2
(Rev.:1999)
(Rev.:1999)
Intersil
HI1-0546-2 Datasheet PDF : 15 Pages
| |||
HI-546, HI-547, HI-548, HI-549
Electrical Specifications Supplies = +15V, -15V; VREF Pin = Open; VAH (Logic Level High) = 4V; VAL (Logic Level Low) = 0.8V; Unless
Otherwise Specified. For Test Conditions, Consult Test Circuits Section (Continued)
PARAMETER
TEST
TEMP
CONDITIONS
(oC)
MIN
-2
TYP MAX
-5, -9
MIN
TYP MAX UNITS
ANALOG CHANNEL CHARACTERISTICS
Analog Signal Range, VIN
On Resistance, rON
Note 2
Full
-15
-
+15
-15
-
+15
V
25
-
1.2
1.5
-
1.5
1.8
kΩ
Full
-
1.5
1.8
-
1.8
2.0
kΩ
∆rON, (Any Two Channels)
Off Input Leakage Current, IS(OFF)
Note 3
25
-
-
7.0
-
-
7.0
%
25
-
0.03
-
-
0.03
-
nA
Full
-
-
50
-
-
50
nA
Off Output Leakage Current, ID(OFF)
HI-546
Note 3
25
-
0.1
-
-
0.1
-
nA
Full
-
-
300
-
-
300
nA
HI-547
Full
-
-
200
-
-
200
nA
HI-548
Full
-
-
200
-
-
200
nA
HI-549
Full
-
-
100
-
-
100
nA
ID(OFF) With Input Overvoltage Applied Note 4
25
-
4.0
-
-
4.0
-
nA
Full
-
-
2.0
-
-
-
µA
On Channel Leakage Current, ID(ON)
HI-546
Note 3
25
-
0.1
-
-
0.1
-
nA
Full
-
-
300
-
-
300
nA
HI-547
Full
-
-
200
-
-
200
nA
HI-548
Full
-
-
200
-
-
200
nA
HI-549
Full
-
-
100
-
-
100
nA
Differential Off Output Leakage Current
IDIFF (HI-547, HI-549 Only)
POWER SUPPLY CHARACTERISTICS
Full
-
-
50
-
-
50
nA
Power Dissipation, PD
Current, I+
Note 7
Full
-
7.5
-
-
7.5
-
mW
Full
-
0.5
2.0
-
0.5
2.0
mA
Current, I-
Note 7
Full
-
0.02
1.0
-
0.02
1.0
mA
NOTES:
2. VOUT = ±10V, IOUT = 100µA.
3. 10nA is the practical lower limit for high speed measurement in the production test environments.
4. Analog Overvoltage = ±33V.
5. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at 25oC.
6. VEN = 0.8V, RL = 1K, CL = 15pF, VS = 7VRMS, f = 100kHz.
7. VEN, VA = 0V or 4V.
8. To drive from DTL/TTLCircuits, 1kΩ pull-up resistors to +5V supply are recommended.
8
Share Link: