MC10H332FN 데이터 시트보기 (PDF) - Motorola => Freescale
부품명
상세내역
일치하는 목록
MC10H332FN Datasheet PDF : 4 Pages
| |||
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Dual Bus Driver/Receiver with
4-to-1 Output Multiplexers
MC10H332
The MC10H332 is a Dual Bus Driver/Receiver with four–to–one output
multiplexers. These multiplexers have common selects and output enable.
When disabled, (OE = high) the bus outputs go to –2.0 V. The parameters
specified are with 25 Ω loading on the bus drivers and 50 Ω loads on the
receivers.
• Propagation Delay, 1.5 ns Typical Data–to–Output
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
L SUFFIX
CERAMIC PACKAGE
CASE 732–03
P SUFFIX
PLASTIC PACKAGE
CASE 738–03
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
VI
Iout
–8.0 to 0
Vdc
0 to VEE
Vdc
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
IE
Input Current High
IinH
Pins 3,4,5,6,14,
15,16,17
Pins 7,8
Pins 13, 18
— 115 — 110 —
— 667 — 417 —
— 437 — 273 —
— 456 — 285 —
115 mA
µA
417
273
285
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
AC PARAMETERS
IinL
VOH
VOL
VIH
VIL
0.5 — 0.5 — 0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
Propagation Delay
tpd
Data–to–Bus Output
Select–to–Bus
Output
OE–to–Bus Output
Bus–to–Receiver
Select–to–Receiver
RE–to–Receiver
Data–to–Receiver
ns
0.8 3.0 0.8 3.0 0.8 3.2
0.8 3.4 0.8 3.4 0.8 3.8
0.8 2.4 0.8 2.4 0.8 2.6
0.8 2.1 0.8 2.1 0.8 2.4
1.8 4.5 1.8 4.5 1.8 5.0
0.8 2.2 0.8 2.2 0.8 2.5
1.3 4.0 1.3 4.0 1.3 4.5
Rise Time
Fall Time
tr
0.5 2.0 0.5 2.0 0.5 2.1 ns
tf
0.5 2.0 0.5 2.0 0.5 2.1 ns
DIP & PLCC
PIN ASSIGNMENT
VCC
1
XBUS
2
X0
3
20
VCC02
19
YBUS
18
OE
X1
4
17
Y0
X2
5
16
Y1
X3
6
15
Y2
S0
7
14
Y3
S1
8
13
RE
XIN
9
VEE
10
12
YIN
11
VCC01
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
NOTE:
Each MECL 10H series circuit has been designed
to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.
3/93
© Motorola, Inc. 1996
2–13
REV 5
Share Link: 